ASI - 8206-L Folding Shower Seat, Solid Phenolic, White – L Shaped, 33″ Wide – Left Hand, ADA

• Heavy Duty - Round Shaped Rod - 1″ diameter
• Type 304 Stainless Steel - Satin Finish
• Heavy duty solid cast brass plated support posts
• Designed not to turn in support posts
• Surface Mounted

• 0755-SS-18 – 18″ Length (457 mm)
• 0755-SS-24 – 24″ Length (610 mm)

Model / Series
0755-SS

Type
Towel Bar (Heavy-Duty) – Surface Mounted, Stainless Steel

Dimensions
Available in 18″ and 24″ (457 and 610 mm) lengths.

Overall Dimensions
(variable length”) x 2-5/8″ x 2-1/2″ (variable x 67 x 64 mm)

Towel Bar
1″ (25 mm) O.D. x 20 gauge, type 304 stainless steel

Support Posts
Heavy solid cast brass plated to have stainless steel satin finish to match stainless steel

Mounting
Surface Mounted

• Satin Finish

Stainless steel washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Stainless steel should be protected against muriatic acid, caustic or abrasive materials, and harsh cleaning detergents.

Surface mount each support post to wall with three (3) 1/4″ diameter [Ø6] oval, pan or round head fasteners of length and type to suit wall conditions (supplied by installer) through mounting holes in posts.

To mount on stud walls, provide concealed backing at screw points, secured to studs. Backing must comply with local building codes. If concealed backing is not provided, secure with toggle bolts.

To mount on solid walls, use plastic or fiber type plugs or expansion bolts.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of bar is 48″ [1219] Above Finished Floor (AFF) if clear floor forward reach access is provided or 46″ [1168] AFF if side reach over obstruction is only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0755-SS

• Self-closing door mounted to cabinet with stainless steel spring hinge
• Recessed for side wall installation
• 1.5 gal (5.7 liters) dry solids capacity
• Waste container held in place by “Z” clip retainer
• Safety-edged finger grip provides convenient grip for service
• Door, flanges, waste receptacle and cabinet are 22 gauge type 304 stainless steel alloy 18-8
• Type 304 Stainless Steel - Satin Finish
• Recessed

Model
0473

Type
Sanitary Napkin Disposal – Recessed

Overall Dimensions
13″ x 17-1/4″ x 4-1/4″ (330 x 438 x 108 mm)

Wall Opening
11-1/4″ x 15-3/4″ x 4″ (285 x 400 x 102 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Material Gauge
22 Gauge

Mounting
Recessed

Capacity
1.5 gal (5.7 liters) of dry solids

• Satin Finish

Users push door to deposit waste material. Door is self-closing.

Unit is emptied by removing can and removing disposable waxed waste paper bag which is furnished by others.

Waste container is held in place by a “Z” clip retainer to prevent inadvertent dumping of contents.

Unit is mounted in wall recess using #10 self-threading screws (by others) through concealed mounting holes provided.

Top of rough wall opening is 3/4″ [19] below top of unit.

Rough wall opening required is 11-1/4″ x 15-3/4″ x 4″ minimum.

• Product Care & Maintenance
• Technical Data Sheet – 0473

• Automatic touchless operation
• Dispenses liquid soap or gel hand sanitizer
• Seamless drawn construction
• 22 gauge type 304 stainless steel
• Satin Finish
• Translucent removable tank for easy-to-view content level
• LED indicates function and operational condition
• Powered by 6 AA-size batteries (not included)
• Surface or stand mounted
• 33.8 oz. (1000 ml) capacity

Model
20364

Series
Roval™

Type
Automatic Liquid Soap and Gel Hand Sanitizer Dispenser

Dimensions
5-1/2″ x 10-7/8″ x 4″ (140 x 276 x 102 mm)

Construction
22 gauge Type 304 Stainless Steel

Capacity
33.8 oz. (1000 ml) of liquid soaps and gel hand sanitizer

Power
6 AA-size batteries (not included)

Operation
Automatic – Battery Operated – Touchless

Mounting
Surface or Stand Mounted

Sensor Detection Range
3-1/8″ [80 mm] ± 3/8″ [10 mm]

Dispense Volume
Approximately 0.03 oz. [0.8 ml] per activation

Soap Requirements
Proper usage of this dispenser requires, that only soap/lotion/gel hand sanitizer within the following range for viscosity and pH may be used.

Liquid Soap Viscosity Range (mPa·s or cP)
50 – 3.5k

Gel Hand Sanitizer Viscosity Range (mPa·s or cP)
3.5k – 23k

pH Range
5.5 ~ 8.5

• Satin Finish

Unit operates when an object is positioned within the sensing distance below the dispenser. A measured amount of product is pumped from the nozzle for each activation while battery charge is adequate and appropriate viscosity soap or sanitizer is present in the tank.

Locking door provides security and vandal resistance after soap refill and battery replacement.

Use clean product from a closed container when refilling the reservoir. Clean the soap reservoir of residue on a monthly basis before refilling with fresh product.

Clean the exterior housing regularly with a soft cleaning cloth. Do not soak or submerge the unit and do not clean under running water.

The sensor lens may be cleaned with a soft clean cloth lightly dampened with a suitable general-purpose surface cleaner. Avoid abrasive materials that may scratch the sensor lens.

Replace the batteries at intervals appropriate for the level of use and facility maintenance schedule.

Secure concealed base plate to wall using four suitable self-threading screws through the mounting holes provided and appropriate wall anchors or another suitable mounting system.

For compliance with 2010 ADA Accessibility Standards, install unit so that bottom of unit is 48″ [1219 mm] maximum Above Finished Floor (AFF).

Minimum distance to counter top is 12″ [305 mm].

Install six (6) AA-size 1.5V batteries according to the polarity indication in the concealed battery compartment. Fill tank with appropriate viscosity soap or sanitizer to the correct level and lock the door.

For wall installation, ensure the mounting surface is smooth, flat, vertical and clean, with sufficient clearance above the unit for servicing and lock access.

• Product Care & Maintenance
• Soap & Hand Sanitizer Dispensing Chart
• Owner's Manual – 20364
• Mounting Template – 20364
• Technical Data Sheet – 20364

• Horizontal baby changing station
• 100% high-density polyethylene construction
• Surface Mounted
• Low profile – only 4″ (102 mm) deep when closed
• Designed to support an infant up to 3.5 years old and up to 50 lbs (23 kg)
• Bed is shaped to cradle a child’s body
• Easy one-handed operation
• Adjustable two-part safety strap with Sure-Lock latch
• Two integral bag hooks
• Bed-liner dispenser convertible to a multi-fold towel dispenser
• Damped gas spring aids one-handed operation

Model
9012

Type
Baby Changing Station, HORIZONTAL – PLASTIC

Closed Dimensions
36” x 22” x 4” (914 x 559 x 102 mm)

Open Dimensions
36” x 22” x 20-7/16” (914 x 559 x 519 mm)

Construction
High-Density Polyethylene (HDPE)

Mounting
Surface Mounted

Intended Use
Infants up to 3.5 years old and up to 50 lbs (23 kg)

• ADA compliant
• ASTM F-2285 & F-2388 compliant
• ANSI Z535 compliant
• ANSI 117.1 compliant
• Adjustable safety strap with Sure-Lock latch
• Operable with less than 5 lbs force (22.2N)
• No tight grasping, pinching or twisting of the wrist is required for operation

Unit platform is shaped to cradle a child’s body. Unit is easily opened and closed by user with one hand anywhere on top or front edge of bed or using bag hooks/hand grips on sides.

Bed liner/towel dispenser presents liners or towels for user hygiene and convenience. Dispenser lip retains stack for single liner/towel dispensing.

Safety strap is easily adjustable by user for baby size and Sure-Lock latch securely resists opening until released by opposing finger pressure by adult caretaker.

Ensure that the liner compartment is adequately stocked. Thoroughly clean the unit daily with warm water and mild anti-bacterial detergent, rinse with clean water and dry. Do not use abrasive cleaning agents.

Periodically inspect the unit to ensure that it remains securely attached to the wall and that the unit and wall mounting have not been affected by vandalism or abnormal wear.

Surface mount unit using hardware supplied through recessed mounting holes provided. Hardware kit supplied has fasteners suitable for metal or wood stud walls in dry locations and general hollow wall construction where adequate substrate strength is obtained.

Fasteners and anchors for masonry walls are not provided. Wall reinforcement must be suitable to sustain transfer of maximum unit loading.

Locate wall studs at 16″ (406 mm) O.C. for fastening the station. If two wall studs cannot be used, use two screws into one stud and install suitable toggle fasteners securely at the non-stud location.

Attach unit to wall studs with four 1/4″ x 3″ long Philips pan head self-threading screws with flat washers. Where wall studs are not available, attach with four 1/4″-20 x 3″ toggle bolts with flat washers into toggles or expansion nuts.

Installation should be performed by a qualified technician, and the wall and attachment method must be strong enough to support the rated load.

• Product Care & Maintenance
• Installation & Maintenance Instructions – 9012
• Technical Data Sheet – 9012