ASI - 0458 Traditional™ Waste Receptacle (4” Projection, 4” Recess) – Semi-Recessed, 12 Gallons

• Satin finish stainless steel construction
• Type 304 stainless steel
• Robust 16 gauge stainless steel face
• Curved radius edges
• Surface mounted
• 48 fl. oz. (1.4 L) capacity
• All-purpose valve dispenses liquid, lotion and detergent-type soaps
• Tamper-resistant refill window with concealed fastening
• Vandal-resistant hinged filler-top
• 3/16″ concealed piano hinge adds durability

Model
9343

Series
Profile™

Type
Liquid Soap Dispenser – Surface Mounted

Dimensions
7-1/4” x 6-1/2” x 3-11/16” (184 x 165 x 94 mm)

Spout Projection
15/16” (24 mm)

Capacity
48 fl. oz. (1.4 L)

Construction
Type 304 Stainless Steel

Mounting
Surface Mounted

Dispensing
Manual push-button operation

Soap Requirements
Proper usage of this dispenser requires, that only soap within the following range for viscosity and pH may be used.

Viscosity Range (mPa·s or cP)
100 – 2.5k

pH Range
5.5 ~ 8.0

Consumable Type
Liquid Soap

• Satin Finish

Soap is manually dispensed by depressing the push button. Unit is refilled through the hinged door at the top requiring the special key supplied to open.

Soap tank will continue to feed properly until empty. Tank supply is replenished manually according to maintenance needs.

Under normal usage, stainless steel products require regular cleaning with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Soap dispenser valves in low-traffic areas should be wiped regularly to remove air-hardened soap residue from the nozzle spout.

If the dispenser fails to operate because of dried soap or debris, the dispenser may be removed from the wall plate and flushed with hot water as described in the ASI installation and maintenance instructions.

Unit is surface mounted to wall or partition by means of a wall mounting plate and screws. Unit is secured to the mounting plate and locked in place by means of a locking screw installed through the tamper-resistant refill door.

Recommended mounting height for general utility is 42″ (1067 mm) Above Finished Floor (AFF) or 6″ (152 mm) minimum above the wash basin to bottom of unit.

Allow 4″ (102 mm) minimum clearance above the unit for filling.

Mount wall plate vertically with the wide part of the “V” at the top. Use suitable mounting hardware for the wall construction.

Unlock the filler door using the special service key furnished, position the dispenser on the wall plate, press the tank down firmly, and tighten the internal locking screw securely.

For maximum usability and ADA accessibility, the valve may be installed at a maximum of 54″ (1372 mm) AFF for clear-floor side reach, 48″ (1219 mm) AFF for clear-floor forward reach, or 46″ (1168 mm) AFF where side reach over an obstruction is provided.

• Product Care & Maintenance
• Soap & Hand Sanitizer Dispensing Chart
• Installation & Maintenance Instructions – 9343
• Technical Data Sheet – 9343

• Horizontal baby changing station
• Recessed mounting
• Type 304 stainless steel door facing and collar
• Available in Satin Finish or Matte Black Powder Coated finish
• Unit complies with 2010 ADA Accessibility Standards
• Intended use for infants up to 3.5 years old and up to 50 lbs (23kg)
• Bed is designed to cradle a child’s body
• Adjustable two-part vinyl-coated safety strap with Sure-Lock latch
• Integral bag hook
• Bed-liner dispenser convertible to a multi-fold towel dispenser
• Damped gas spring aids one-handed operation using less than 5 lbs force (22.2N)

Series
9018 Series

Models
9018 / 9018-41

Type
Baby Changing Station, HORIZONTAL – STAINLESS STEEL, Recessed

Closed Dimensions
39-5⁄32″ x 28-1/4″ x 3⁄8″ (995 x 718 x 10 mm)

Open Dimensions
39-5/32” x 28-1/4” x 18-1/8” (995 x 718 x 460 mm)

Wall Opening
35-1/2″ x 24-1/2″ x 4″ min (902 x 622 x 102 mm)

Construction
Type 304 Stainless Steel

Mounting
Recessed

9018 Finish
Satin Finish

9018-41 Finish
Matte Black Powder Coated

Intended Use
Infants up to 3.5 years old and up to 50 lbs (23kg)

Static Load Testing
Tested during development to sustain 250 lbs (113 kg) static load with minimal deflection.

• 9018 – Type 304 Stainless Steel - Satin Finish
• 9018-41 – Type 304 Stainless Steel - Matte Black Powder Coated

• Complies with 2010 ADA Accessibility Standards
• ASTM F-2285 & F-2388 compliant
• G-21 and G-22 compliant
• ANSI Z535 compliant
• ANSI 117.1 compliant
• EN 12221-1 and EN 12221-2 compliant
• Adjustable two-part vinyl-coated safety strap with Sure-Lock latch
• Operable using less than 5 lbs force (22.2N)

Unit platform is shaped to keep a child restrained from rolling out of the bed. Unit is easily opened and closed by user with one hand in any location and handle cavity is provided on door face for preferred use.

Unit is operable with less than 5 Lbf (22.2N) while not requiring any tight grasping, pinching or twisting of the wrist.

Bed liner/towel dispenser presents liners or towels for user hygiene and convenience. Dispenser lid is provided for sanitary protection and ease of loading of wipes or liners.

Safety strap is easily adjustable by user for baby size and Sure-Lock latch securely resists opening until released by opposing finger pressure by adult caretaker/parent.

Liners/towels are easily replenished by service personnel as required.

Unit is recess mounted using hardware supplied through concealed mounting holes. The supplied hardware kit contains fasteners suitable for metal or wood stud walls in dry locations and general hollow wall construction where adequate substrate strength is obtained.

Fasteners and anchors for masonry walls are not provided. Wall reinforcement must be suitable to sustain transfer of maximum unit loading.

Mounting hole plug covers are supplied to conceal fasteners after installation.

Provide Rough Wall Opening (RWO) of required depth from face of finished wall. Mount unit in properly framed RWO using four (4) #10 x 1-1/2″ [M5 x 38] self-threading pan head screws through side holes.

Alternate rear-hole mounting may be used where wall depth and framing reinforcement permits, using suitable fasteners appropriate for wall conditions.

Rough Wall Opening (RWO) required is 35-1/2″ W x 24-1/2″ H x 4″ D minimum [902 x 622 x 102].

• Product Care & Maintenance
• Installation, Maintenance & Operation Owner's Manual – 9018 Series
• Technical Data Sheet – 9018 – Satin Finish
• Technical Data Sheet – 9018-41 – Matte Black

• Heavy Duty - Round Shaped Rod - 1″ diameter
• Type 304 Stainless Steel - Satin Finish
• Heavy duty solid cast brass plated support posts
• Designed not to turn in support posts
• Surface Mounted

• 0755-SS-18 – 18″ Length (457 mm)
• 0755-SS-24 – 24″ Length (610 mm)

Model / Series
0755-SS

Type
Towel Bar (Heavy-Duty) – Surface Mounted, Stainless Steel

Dimensions
Available in 18″ and 24″ (457 and 610 mm) lengths.

Overall Dimensions
(variable length”) x 2-5/8″ x 2-1/2″ (variable x 67 x 64 mm)

Towel Bar
1″ (25 mm) O.D. x 20 gauge, type 304 stainless steel

Support Posts
Heavy solid cast brass plated to have stainless steel satin finish to match stainless steel

Mounting
Surface Mounted

• Satin Finish

Stainless steel washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Stainless steel should be protected against muriatic acid, caustic or abrasive materials, and harsh cleaning detergents.

Surface mount each support post to wall with three (3) 1/4″ diameter [Ø6] oval, pan or round head fasteners of length and type to suit wall conditions (supplied by installer) through mounting holes in posts.

To mount on stud walls, provide concealed backing at screw points, secured to studs. Backing must comply with local building codes. If concealed backing is not provided, secure with toggle bolts.

To mount on solid walls, use plastic or fiber type plugs or expansion bolts.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of bar is 48″ [1219] Above Finished Floor (AFF) if clear floor forward reach access is provided or 46″ [1168] AFF if side reach over obstruction is only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0755-SS

• Self-closing door mounted to cabinet with stainless steel spring hinge
• Recessed for side wall installation
• 1.5 gal (5.7 liters) dry solids capacity
• Waste container held in place by “Z” clip retainer
• Safety-edged finger grip provides convenient grip for service
• Door, flanges, waste receptacle and cabinet are 22 gauge type 304 stainless steel alloy 18-8
• Type 304 Stainless Steel - Satin Finish
• Recessed

Model
0473

Type
Sanitary Napkin Disposal – Recessed

Overall Dimensions
13″ x 17-1/4″ x 4-1/4″ (330 x 438 x 108 mm)

Wall Opening
11-1/4″ x 15-3/4″ x 4″ (285 x 400 x 102 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Material Gauge
22 Gauge

Mounting
Recessed

Capacity
1.5 gal (5.7 liters) of dry solids

• Satin Finish

Users push door to deposit waste material. Door is self-closing.

Unit is emptied by removing can and removing disposable waxed waste paper bag which is furnished by others.

Waste container is held in place by a “Z” clip retainer to prevent inadvertent dumping of contents.

Unit is mounted in wall recess using #10 self-threading screws (by others) through concealed mounting holes provided.

Top of rough wall opening is 3/4″ [19] below top of unit.

Rough wall opening required is 11-1/4″ x 15-3/4″ x 4″ minimum.

• Product Care & Maintenance
• Technical Data Sheet – 0473