Soap Dispensers

• Automatic touchless operation
• Dispenses liquid soap or gel hand sanitizer
• Seamless drawn construction
• 22 gauge type 304 stainless steel
• Satin Finish
• Translucent removable tank for easy-to-view content level
• LED indicates function and operational condition
• Powered by 6 AA-size batteries (not included)
• Surface or stand mounted
• 33.8 oz. (1000 ml) capacity

Model
20364

Series
Roval™

Type
Automatic Liquid Soap and Gel Hand Sanitizer Dispenser

Dimensions
5-1/2″ x 10-7/8″ x 4″ (140 x 276 x 102 mm)

Construction
22 gauge Type 304 Stainless Steel

Capacity
33.8 oz. (1000 ml) of liquid soaps and gel hand sanitizer

Power
6 AA-size batteries (not included)

Operation
Automatic – Battery Operated – Touchless

Mounting
Surface or Stand Mounted

Sensor Detection Range
3-1/8″ [80 mm] ± 3/8″ [10 mm]

Dispense Volume
Approximately 0.03 oz. [0.8 ml] per activation

Soap Requirements
Proper usage of this dispenser requires, that only soap/lotion/gel hand sanitizer within the following range for viscosity and pH may be used.

Liquid Soap Viscosity Range (mPa·s or cP)
50 – 3.5k

Gel Hand Sanitizer Viscosity Range (mPa·s or cP)
3.5k – 23k

pH Range
5.5 ~ 8.5

• Satin Finish

Unit operates when an object is positioned within the sensing distance below the dispenser. A measured amount of product is pumped from the nozzle for each activation while battery charge is adequate and appropriate viscosity soap or sanitizer is present in the tank.

Locking door provides security and vandal resistance after soap refill and battery replacement.

Use clean product from a closed container when refilling the reservoir. Clean the soap reservoir of residue on a monthly basis before refilling with fresh product.

Clean the exterior housing regularly with a soft cleaning cloth. Do not soak or submerge the unit and do not clean under running water.

The sensor lens may be cleaned with a soft clean cloth lightly dampened with a suitable general-purpose surface cleaner. Avoid abrasive materials that may scratch the sensor lens.

Replace the batteries at intervals appropriate for the level of use and facility maintenance schedule.

Secure concealed base plate to wall using four suitable self-threading screws through the mounting holes provided and appropriate wall anchors or another suitable mounting system.

For compliance with 2010 ADA Accessibility Standards, install unit so that bottom of unit is 48″ [1219 mm] maximum Above Finished Floor (AFF).

Minimum distance to counter top is 12″ [305 mm].

Install six (6) AA-size 1.5V batteries according to the polarity indication in the concealed battery compartment. Fill tank with appropriate viscosity soap or sanitizer to the correct level and lock the door.

For wall installation, ensure the mounting surface is smooth, flat, vertical and clean, with sufficient clearance above the unit for servicing and lock access.

• Product Care & Maintenance
• Soap & Hand Sanitizer Dispensing Chart
• Owner's Manual – 20364
• Mounting Template – 20364
• Technical Data Sheet – 20364

• Satin finish stainless steel construction
• Type 304 stainless steel
• Robust 16 gauge stainless steel face
• Curved radius edges
• Surface mounted
• 48 fl. oz. (1.4 L) capacity
• All-purpose valve dispenses liquid, lotion and detergent-type soaps
• Tamper-resistant refill window with concealed fastening
• Vandal-resistant hinged filler-top
• 3/16″ concealed piano hinge adds durability

Model
9343

Series
Profile™

Type
Liquid Soap Dispenser – Surface Mounted

Dimensions
7-1/4” x 6-1/2” x 3-11/16” (184 x 165 x 94 mm)

Spout Projection
15/16” (24 mm)

Capacity
48 fl. oz. (1.4 L)

Construction
Type 304 Stainless Steel

Mounting
Surface Mounted

Dispensing
Manual push-button operation

Soap Requirements
Proper usage of this dispenser requires, that only soap within the following range for viscosity and pH may be used.

Viscosity Range (mPa·s or cP)
100 – 2.5k

pH Range
5.5 ~ 8.0

Consumable Type
Liquid Soap

• Satin Finish

Soap is manually dispensed by depressing the push button. Unit is refilled through the hinged door at the top requiring the special key supplied to open.

Soap tank will continue to feed properly until empty. Tank supply is replenished manually according to maintenance needs.

Under normal usage, stainless steel products require regular cleaning with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Soap dispenser valves in low-traffic areas should be wiped regularly to remove air-hardened soap residue from the nozzle spout.

If the dispenser fails to operate because of dried soap or debris, the dispenser may be removed from the wall plate and flushed with hot water as described in the ASI installation and maintenance instructions.

Unit is surface mounted to wall or partition by means of a wall mounting plate and screws. Unit is secured to the mounting plate and locked in place by means of a locking screw installed through the tamper-resistant refill door.

Recommended mounting height for general utility is 42″ (1067 mm) Above Finished Floor (AFF) or 6″ (152 mm) minimum above the wash basin to bottom of unit.

Allow 4″ (102 mm) minimum clearance above the unit for filling.

Mount wall plate vertically with the wide part of the “V” at the top. Use suitable mounting hardware for the wall construction.

Unlock the filler door using the special service key furnished, position the dispenser on the wall plate, press the tank down firmly, and tighten the internal locking screw securely.

For maximum usability and ADA accessibility, the valve may be installed at a maximum of 54″ (1372 mm) AFF for clear-floor side reach, 48″ (1219 mm) AFF for clear-floor forward reach, or 46″ (1168 mm) AFF where side reach over an obstruction is provided.

• Product Care & Maintenance
• Soap & Hand Sanitizer Dispensing Chart
• Installation & Maintenance Instructions – 9343
• Technical Data Sheet – 9343

• Vertical space saving footprint
• All purpose valve and a tamper-resistant refill indicator
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• Manual Push Button Operation
• Liquid Soap - 40 oz. (1.2 L) Capacity

Model
0347

Type
Liquid Soap Dispenser – Vertical – Surface Mounted

Dimensions
4-13/16” x 8-3/16” x 3-15/16” (122 x 208 x 100 mm)

Spout Projection
3⁄4″ (19 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Mounting
Surface Mounted

Capacity
40 fl. oz. (1.2 L)

Operation
Manual Push Button Operation

Soap Requirements
Proper usage of this dispenser requires, that only soap within the following range for viscosity and pH may be used.

Viscosity Range (mPa·s or cP)
100 – 3.5k

pH Range
5.5 ~ 8.5

Soaps containing reportable salts, chlorides and alcohols should be avoided.

• Satin Stainless Steel

Push button to dispense soap. Unit is refilled through hinged door at top requiring special key (supplied) to open.

Soap tank will continue to feed properly until soap level is below valve intake port. Tank supply is replenished manually.

Unit is surface mounted to wall or partition with a wall mounting plate (supplied) and screws (by others). Unit is secured to interlocking wedge bracket and locked in place by a locking screw (supplied) installed through hinged refill door.

Recommended installation for general utility is 42" [1066] Above Finished Floor (AFF) or 6" [152] min above washbasin.

For compliance with 2010 ADA Accessibility Standards and 2015 ABA Standards, install unit with centerline of valve button no higher than 48" [1219] AFF.

• Product Care & Maintenance
• Soap Dispensing Chart
• Technical Data Sheet – 0347