Toilet Accessories

• Single robe hook
• Fabricated from rust resistant Zamak
• Stainless steel wall bracket
• Stainless steel hex socket set screw provided along base of flange
• Chrome Plated
• Surface Mounted

Model
0740-Z

Type
Robe Hook (Single)

Dimensions
2-1/8″ x 1-7/16″ x 2-1/8″ (54 x 37 x 54 mm)

Construction
Chrome Plated Zamac

Wall Bracket
Stainless Steel

Mounting
Surface Mounted

• Chrome Plated

Washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Wall bracket is surface mounted using #10 self-threading screws (supplied) through holes provided. Hook is secured to bracket by tightening stainless steel hex socket set screw.

Typical mounting suggestion is 66″ [1676] Above Finished Floor (AFF).

For compliance with 2010 ADA Accessibility Standards, unit should be installed so that top of hook is 54″ [1372] maximum AFF if clear floor side reach access is provided or 48″ [1219] maximum AFF if clear floor forward reach access is provided.

• Product Care & Maintenance
• Technical Data Sheet – 0740-Z

• Heavy-duty robe hook
• Fabricated of brass with a chrome finish
• Exposed mounting
• Three (3) 7/32″ diameter (Ø5.6) countersunk mounting holes
• 2-3/4″ diameter (Ø70) flange
• Surface Mounted
• Capable of supporting over 181 lbs. (82 kg) when properly attached to building element

Model
0751-A

Type
Robe Hook (Heavy-Duty) – Surface Mounted (Exposed)

Dimensions
2-3/4″ x 2-3/4″ x 3-1/4 Projection (70 x 70 x 83 mm)

Construction
Heavy Duty Chrome Plated Brass

Mounting
Surface Mounted (Exposed)

Flange Diameter
2-3/4″ (Ø70)

Capacity
Hook is capable of supporting over 181 lbs. (82 kg) when properly attached to building element.

• Satin Chrome

Washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Unit is surface mounted on wall or partition using stainless steel Philips flat or oval head #10 self-threading screws (provided by others to suit wall conditions) in a manner capable of supporting 181 lbs (82 kg).

Ensure that mounting configuration complies with local building codes.

For compliance with 2010 ADA Accessibility Standards install the hook center-line 54″ [1372] maximum Above Finished Floor (AFF) when clear floor side reach access is provided or 48″ [1219] max AFF with clear floor forward reach access only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0751-A

• Jumbo Twin Roll Dispenser
• Holds two 9″ (229 mm) diameter rolls
• Accommodates 2-1⁄4″ or 3″ (57 or 76 mm) diameter cores
• Slide panel exposes other roll when one roll is depleted
• Door cabinet and mounting plate fabricated of 18 gauge type 304 stainless steel with a satin finish
• Two viewing slots reveal toilet tissue rolls inside
• Equipped with tumbler lock
• Surface Mounted

Model
0040

Type
Twin 9″ Jumbo Roll Toilet Tissue Dispenser

Dimensions
20-13⁄16″ x 11-3⁄8″ x 6-3⁄16″ (529 x 289 x 157 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Cabinet & Mounting Plate
18 gauge Type 304 stainless steel

Mounting
Surface Mounted

Capacity
Holds two 9″ (229 mm) diameter rolls

Core Sizes
2-1⁄4″ or 3″ (57 or 76 mm) diameter core

• Satin Finish

Two (2) 9″ [Ø229] outside diameter jumbo rolls of toilet tissue are mounted over 3″ [Ø76] inside diameter (ID) core adapters. Two (2) 2-1/4″ [Ø57] ID core rolls may be used by removing the core adapters.

Whenever one roll of toilet tissue is depleted, the other roll is selected by shifting over the lever at the bottom of the unit.

Viewing slots continuously reveal tissue level. Keylocked door prevents unauthorized access or removal. Tissue supply is replenished on a cycle determined by maintenance needs.

For general utility surface mount unit within 12″ [305] of front of toilet from center line and 31″ [787] above finished floor (AFF) from bottom of unit with five (5) No. 12 x 3/4″ [Ø5.5 x 20] pan head self threading screws (by others), or other types as more suitable to site conditions (by others), including wall type appropriate anchors (by others) as may be required through mounting holes provided.

For compliance with 2010 ADA Accessibility Standards install unit so that centerline of first roll is between 7″ and 9″ [178 to 229] from front of toilet and centerline of rolls is 19″ [483] minimum above finished floor (AFF) to 44″ [1118] max. AFF.

• Product Care & Maintenance
• Technical Data Sheet – 0040

• Single Roll Dispenser
• Type 304 Stainless Steel
• Chrome-plated roller
• Heavy gauge concealed bracket mounts on wall
• Secured with stainless steel set screw
• Holds 1800 sheet standard core roll
• Mounting plates are 18 gauge steel
• Surface Mounted
• For theft-resistant spindle, add R-009 after model number

Series
7305 Series

Type
Toilet Tissue Holder (Single)

Dimensions
7-3/4″ x 2″ x 3-7/8″ (207 x 51 x 98 mm)

Construction
Type 304 Stainless Steel

Roller
Chrome-plated roller

Mounting Plates
18 gauge steel

Mounting
Surface Mounted

Capacity
Holds 1800 sheet standard core roll

• 7305-B – Bright Finish
• 7305-S – Satin Finish

Spring-loaded spindles revolve freely and hold rolls until cores are removed.

Surface mount unit on wall using #10 self-threading screws (by others) through holes provided in mounting plates into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit wall conditions.

Hang post and flange assemblies on mounting plates and tighten setscrews to lock units to plates.

For compliance with ICC/ANSI A-117.1-2003 and 2010 ADA Accessibility Standards install unit so that center line of dispenser is 7″ [178] min to 9″ [229] Max in front of toilet and dispenser center is 15″ [381] Min AFF to 48″ [1219] Max AFF.

Recommended mounting height for general utility is 30″ [762] AFF to centerline of roll and 14″ [356] from front of commode to centerline of dispenser.

• Product Care & Maintenance
• Technical Data Sheet – 7305-B – Bright Finish
• Technical Data Sheet – 7305-S – Satin Finish

• Straight Grab Bar
• Snap Flange - cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Smooth surface
• Surface Mounted
• 18 gauge tubing with 1-1/4″ Outside Diameter [Ø32]
• Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples
• Mounting flange is 1/8″ (3 mm) thick, type 304 stainless steel
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter

• 18″ (457 mm) – 3701-18
• 36″ (914 mm) – 3701-36
• 42″ (1067 mm) – 3701-42

Series
3701 Series

Type
Straight Grab Bar

Tubing
18 gauge tubing with 1-1/4″ Outside Diameter [Ø32]

Construction
Type 304 Stainless Steel - Satin Finish

Surface
Smooth

Mounting
Surface Mounted

Wall Clearance
1-1/2″ [38]

Mounting Flange
Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples; 1/8″ (3 mm) thick, type 304 stainless steel.

Cover
Type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter.

ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 that fabricated product shall be of adequate strength to support a load in excess of 250 pounds (113.4 kg). Mounting to the wall is a critical part of the system to meet this requirement. The fastener system must be adequately sized to withstand the shear, tension or pullout, and torsion loads generated by the maximum loading.

• Satin Finish

Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using two (2) #10 self-threading flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33″ [840] minimum Above Finished Floor (AFF) to 36″ [915] maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series).

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 3701-18
• Technical Data Sheet – 3701-36
• Technical Data Sheet – 3701-42

• Low Profile - Twin Jumbo Roll Dispenser
• Holds two 9″ (229 mm) diameter rolls
• Accommodates 2-1⁄4″ or 3″ (57 or 76 mm) diameter cores
• Slide panel exposes other roll when one roll is depleted
• Door cabinet and mounting plate fabricated of 18 gauge type 304 stainless steel with a satin finish
• Heavy-duty stainless steel pivot hinges
• Equipped with tumbler lock
• Viewing slot provides easy visual indication of remaining tissue supply
• Surface Mounted

Model
0039

Type
Low Profile 9″ Jumbo Roll Toilet Tissue Dispenser

Dimensions
20-1⁄2″ x 11-3⁄16″ x 4-11⁄16″ (521 x 284 x 119 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Cabinet & Mounting Plate
18 gauge Type 304 stainless steel

Mounting
Surface Mounted

Capacity
Holds two 9″ (229 mm) diameter rolls

Core Sizes
2-1⁄4″ or 3″ (57 or 76 mm) diameter core

• Type 304 Stainless Steel - Satin Finish

Two (2) 9″ [Ø229] outside diameter jumbo rolls of toilet tissue are mounted over 3″ [Ø76] inside diameter (ID) core adapters. Two (2) 2-1/4″ [Ø57] ID core rolls may be used by removing the core adapters.

Whenever one roll of toilet tissue is depleted, the other roll is selected by shifting over the lever at the bottom of the unit.

Viewing slot continuously reveals tissue level. Key and locked door prevents unauthorized access or removal. Tissue supply is replenished on a cycle determined by maintenance needs.

Surface mount unit for general utility within 12″ [305] of front of toilet from centerline and 31″ [787] above finished floor (AFF) from bottom of unit with five (5) No. 12 x 3/4″ [Ø5.5 x 20] pan head self threading screws (by others), or other types as more suitable to site conditions (by others), including wall type appropriate anchors (by others) as may be required through mounting holes provided.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of nearest roll is between 7″ to 9″ [178 to 229] from front of commode and centerline of rolls is 19″ [483] minimum AFF to 44″ [1118] max AFF.

• Product Care & Maintenance
• Technical Data Sheet – 0039

• Dispenses 250 single or half-fold seat covers
• Fabricated of 22 gauge type 304 stainless steel with satin finish
• Heavy-duty 3/16″ Dia. [Ø4.8] stainless steel multi-staked piano hinged door
• Door includes tumbler lock
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted

Model
0477-SM

Type
Toilet Seat Cover Dispenser – Surface Mounted

Dimensions
15-3/4” x 11” x 1-7/8” (400 x 279 x 48 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Cabinet
22 gauge

Mounting
Surface Mounted

Capacity
Dispenses 250 standard single or half-fold paper toilet seat covers

• Type 304 Stainless Steel - Satin Finish

Covers are self-feeding until supply is depleted. Unit is manually reloaded with a full box through concealed opening in bottom on schedule determined by maintenance requirements.

Unit is surface mounted on wall or partition using two (2) #10 x 1-1/2″ [Ø5 x 40] self-threading screws (by others).

Mounting holes are hidden behind dispenser box for vandal resistant locking but clearly accessible through dispenser slot for installation hanging.

For compliance with 2010 ADA Accessibility Standards, unit should be installed so that dispenser slot is 54″ [1372] maximum above finished floor (AFF) if clear floor side reach access is provided or 48″ [1219] maximum AFF if clear floor forward reach access only is provided or 46″ [1168] maximum AFF if side reach over an obstruction only is provided (ie: vanity).

• Product Care & Maintenance
• Technical Data Sheet – 0477-SM

• Straight Grab Bar
• Snap Flange – cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Peened for better gripping
• Surface Mounted
• Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples
• Mounting flange is 1/8″ (3 mm) thick, type 304 stainless steel
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter

• 18″ (457 mm) – 10-3801-18P
• 36″ (914 mm) – 10-3801-36P
• 42″ (1067 mm) – 3801-42P

Series
3801 Series

Type
Straight Grab Bar – Peened

Dimensions
1-1⁄4″ (32 mm) O.D.

Construction
Type 304 Stainless Steel - Satin Finish

Surface
Peened

Mounting
Surface Mounted

Mounting Flange
Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples; 1/8″ (3 mm) thick, type 304 stainless steel.

Cover
Type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter.

ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1. The fabricated product is designed to support a load in excess of 250 pounds (113.4 kg). Proper wall mounting, anchoring and an adequately sized fastener system are required to meet the specified loading requirements.

• Satin Finish - Peened for better gripping

Use the grab bar as a template to locate and pre-drill the mounting holes. Install each flange with two appropriate #10 self-threading flat or oval head screws or another fastener system suitable for the wall conditions.

Appropriate anchoring and backing must be provided in accordance with applicable building requirements or the architect's plans before the wall is finished.

For 2010 ADA Accessibility Standards, the top of the grab bar should be installed between 33″ [840] minimum and 36″ [915] maximum Above Finished Floor (AFF).

ASI anchors are available separately and should be specified according to the grab bar and mounting conditions.

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 10-3801-18P
• Technical Data Sheet – 10-3801-36P
• Technical Data Sheet – 10-3801-42P

• "Hide-A-Roll" dispenser holds two rolls
• Holds two rolls up to 5 1/4″ (133 mm) diameter
• 1800 sheet capacity
• Top roll automatically drops in place when bottom roll is used up
• Theft resistant spindles
• Tumbler lock
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted

Model
0030

Type
Toilet Tissue Dispenser, Twin Hide-A-Roll

Dimensions
6″ x 12″ x 6 1/2″ (152 x 305 x 165 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Door
18 gauge Type 304 stainless steel

Cabinet Body & Dispensing Mechanism
22 gauge Type 304 stainless steel

Mounting
Surface Mounted

Capacity
Holds two rolls up to 5 1/4″ (133 mm) diameter (1800 sheets)

• Type 304 Stainless Steel - Satin Finish

Reloading instructions are printed on graphic label inside door.

Bottom roll is depleted prior to top roll automatically dropping into lower position for use.

Empty rollers cannot be removed without key unlocking door.

Unit is surface mounted on wall or partition using four (4) 1/4″ x 1″ [M6 x 25] Philips pan-head self-threading screws (by others) through slots on rear wall into suitable wall preparation (by others).

Top two (2) mounting holes through back are "keyhole" slots for ease in hanging unit on pre-installed screws. Bottom two (2) mounting holes are horizontal slots for ease of adjustment.

For compliance with 2010 ADA Accessibility Standards and 2015 ABA Standards install unit with axis of bottom roller 15″ [381] min AFF (Above Finished Floor) to 48″ [1219] max AFF and centerline of dispenser shall be 7″ [178] min to 9″ [229] max. in front of toilet.

• Product Care & Maintenance
• Technical Data Sheet – 0030

• Double Hook
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• 4″ (102 mm) wide stainless steel bar forms hook at each end
• Hook is suitable for robes or clothing and small carry bags

Model
7345-S

Type
Robe Hook (Double)

Dimensions
4″ x 2″ x 2″ (102 x 51 x 51 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Mounting
Surface Mounted

• 7345-B – Bright Finish
• 7345-S – Satin Finish

Hook is suitable for a robe or clothing and small carry bags.

Surface mount unit on door back or wall using two (2) #10 self-threading screws (by others) through holes provided in mounting plate into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit door or wall conditions. Hang post and flange assembly on mounting plate and tighten set screw to lock unit to plate.

For compliance with ICC/ANSI A-117.1-2003 and 2010 ADA Accessibility Standards, install unit with top of hook 48″ [1219] maximum Above Finished Floor (AFF) or 46″ [1168] max AFF if side reach access over an obstruction (e.g. vanity) with reach depth greater than 10″ [254] and less than 25″ [635] is only provided or 44″ [1118] max AFF if forward reach over an obstruction with reach depth greater than 20″ [508] and less than 25″ [635] is only provided.

For general utility, install hook with centerline of mounting plate 68″ [1727] AFF.

• Product Care & Maintenance
• Technical Data Sheet – 7345-S
• Technical Data Sheet – 7345-B

• Single Hook
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• Hook extends 2" [51] from wall
• Hook is suitable for a robe or clothing and small carry bags

Model
7340-S

Type
Robe Hook (Single)

Dimensions
2" [51] W x 2" [51] H x 2" [51] D

Construction
Type 304 Stainless Steel - Satin Finish

Mounting
Surface Mounted

• 7340-B – Bright Finish
• 7340-S – Satin Finish

Hook is suitable for a robe or clothing and small carry bags.

Surface mount unit on door back or wall using two (2) #10 self-threading screws (by others) through holes provided in mounting plate into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit door or wall conditions.

Hang post and flange assembly on mounting plate and tighten set screw to lock unit to plate.

For compliance with ICC/ANSI A-117.1-2003 and 2010 ADA Accessibility Standards, install unit with top of hook 48" [1219] maximum Above Finished Floor (AFF) or 46" [1168] max AFF if side reach access over an obstruction (e.g. vanity) with reach depth greater than 10" [254] and less than 25" [635] is only provided or 44" [1118] max AFF if forward reach over an obstruction with reach depth greater than 20" [508] and less than 25" [635] is only provided.

For general utility, install hook with centerline of mounting plate 68" [1727] AFF.

• Product Care & Maintenance
• Technical Data Sheet – 7340-S
• Technical Data Sheet – 7340-B

• Straight Grab Bar
• Snap Flange - cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• 18 gauge tubing with 1-1/2" Outside Diameter [Ø38]
• Concealed mounting flange of 3-1/8" [79] O.D. with 2 screw holes and 3 locking dimples
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16" [81] diameter

Type
Straight Grab Bar

Material
Type 304 Stainless Steel

Construction
18 gauge tubing with 1-1/2" Outside Diameter [Ø38]

Mounting
Surface Mounted

Mounting Flange
3-1/8" [79] O.D. with 2 screw holes and 3 locking dimples

Mounting Capacity
ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 that fabricated product shall be of adequate strength to support a load in excess of 250 pounds (113.4 kg). Mounting to the wall is a critical part of the system to meet this requirement. The fastener system must be adequately sized to withstand the shear, tension or pullout, and torsion loads generated by the maximum loading.

• 42" / 10-3801-42
• 36" / 10-3801-36
• 18" / 10-3801-18

Stainless Steel
Satin finish, unless otherwise noted.

Stainless Steel washroom accessory products require regular surface cleaning, much the same as stainless steel sinks, pots and pans and eating utensils.

As long as a regular cleaning schedule is followed, the best method is cleaning with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

For a “new" look, surfaces can be wiped with lemon oil applied by a soft polishing cloth to maintain sheen.

Stainless Steel should be protected against muriatic acid and caustic or abrasive materials, and harsh cleaning detergents [with pH outside the range 7 ± 1.5].

In the event such agents cause discoloration, polishing with a stainless steel cleaner such as 3M™ Stainless Steel Cleaner & Polish® and a soft cloth on bright or mirror finishes, or for satin finish surfaces the Stainless Steel cleaner and 3M™ Scotch Brite® pad either blue (less aggressive) or green (more aggressive) is recommended.

Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using two (2) #10 selfthreading flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" [840] minimum Above Finished Floor (AFF) to 36" [915] maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series).

• Product Care & Maintenance
• Grab Bar Configurations

Technical Data Sheets

• 42" / 10-3801-42 – Technical Data Sheet
• 36" / 10-3801-36 – Technical Data Sheet
• 18" / 10-3801-18 – Technical Data Sheet