Shower / Tub Accessories

• Square shaped towel bar
• Fabricated from triple chrome plated rust-resistant Zamak
• 3/4″ (19 mm) square steel tubing
• 21 gauge (.032 in. <.81 mm> wall) tubing
• Triple chrome plated steel tubing
• Surface mounted
• Available in 18″ and 24″ lengths

• 0760-Z-18 – 18″ Length (457 mm)
• 0760-Z-24 – 24″ Length (610 mm)

Model / Series
0760-Z

Type
Towel Bar (Square) – Surface Mounted, Chrome Plated Zamak

Dimensions
18-36″ x 1-7/16″ x 3-3/16″ (457-914 x 37 x 81 mm)

Bar
3/4″ (19 mm) Square, 21 Gauge Steel Tubing

Construction
Chrome Plated Zamak with Triple Chrome Plated Steel Tubing

Mounting
Surface Mounted

• Triple Chrome Plated

Washroom accessory products require regular surface cleaning. As long as a regular cleaning schedule is followed, clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

For general utility, mount bar 50″ (1270 mm) Above Finished Floor (AFF) from center line of towel bar.

Locate wall brackets in appropriate positions and secure wall plates with two (2) self-threading screws (by others) through two slot holes in wall plates.

Install brackets over wall plates and fasten in place with stainless steel set screws through tapped holes in brackets.

• Product Care & Maintenance
• Technical Data Sheet – 0760-Z

• Heavy Duty - Round Shaped Rod - 1″ diameter
• Type 304 Stainless Steel - Satin Finish
• Heavy duty solid cast brass plated support posts
• Designed not to turn in support posts
• Surface Mounted

• 0755-SS-18 – 18″ Length (457 mm)
• 0755-SS-24 – 24″ Length (610 mm)

Model / Series
0755-SS

Type
Towel Bar (Heavy-Duty) – Surface Mounted, Stainless Steel

Dimensions
Available in 18″ and 24″ (457 and 610 mm) lengths.

Overall Dimensions
(variable length”) x 2-5/8″ x 2-1/2″ (variable x 67 x 64 mm)

Towel Bar
1″ (25 mm) O.D. x 20 gauge, type 304 stainless steel

Support Posts
Heavy solid cast brass plated to have stainless steel satin finish to match stainless steel

Mounting
Surface Mounted

• Satin Finish

Stainless steel washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Stainless steel should be protected against muriatic acid, caustic or abrasive materials, and harsh cleaning detergents.

Surface mount each support post to wall with three (3) 1/4″ diameter [Ø6] oval, pan or round head fasteners of length and type to suit wall conditions (supplied by installer) through mounting holes in posts.

To mount on stud walls, provide concealed backing at screw points, secured to studs. Backing must comply with local building codes. If concealed backing is not provided, secure with toggle bolts.

To mount on solid walls, use plastic or fiber type plugs or expansion bolts.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of bar is 48″ [1219] Above Finished Floor (AFF) if clear floor forward reach access is provided or 46″ [1168] AFF if side reach over obstruction is only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0755-SS

• L Shaped – Left Hand – 33″ (838 mm) Wide – ADA
• Seat folds up when not in use
• Requires only one hand operation to manually lower to horizontal position for use or raise for departure and arrival
• White solid phenolic seat with black core
• Frame, support legs, flanges, and bracket are type 304 satin finish stainless steel
• Phenolic seat ONLY is field reversible
• Seat is slotted for drainage
• Surface Mounted
• Supports loads up to 500 lbs maximum if installed properly

Model
8206-L

Type
Folding Shower Seat – L Shaped – Left Hand

Seat
½” (13 mm) thick, one piece solid, white colored, black core phenolic

Width
33″ (838 mm)

Projection
22-7⁄8″ (581 mm) from wall

Fold Down Dimensions
33″ x 17″ x 22-7/8″ (838 x 432 x 581 mm)

Fold Up Dimensions
33″ x 35-3/8″ x 22-7/8″ (457 x 899 x 581 mm)

Frame Construction
Type 304 Stainless Steel – Satin Finish

Mounting
Surface Mounted

Compliance
ADA

Supports loads up to 500 lbs maximum if installed properly.

• Seat: White Phenolic with Black Core
• Frame / Body: Type 304 Stainless Steel – Satin Finish

Fold-up Shower Seat requires only one hand operation to manually lower to horizontal position for use or raise for departure and arrival.

Guide bracket with spring detent prevents seat from dropping and provides positive support in usage position as well as spring locked storage position.

This unit is surface mounted. Installer/contractor must provide concealed anchor plate or blocking as specified in construction documents or as required by local building codes prior to wall finishing.

Fasten unit flanges and guide bracket to concealed anchor or blocking plate with appropriate hardware.

Concealed mounting plates or anchors and hardware are not supplied with this product and must be specified separately.

Ensure that mounting configuration complies with local building codes.

• Product Care & Maintenance
• Technical Data Sheet – 8206-L