ASI - 0852 Sanitary Napkin Disposal – Surface Mounted

• Heavy Duty - Round Shaped Rod - 1″ diameter
• Type 304 Stainless Steel - Satin Finish
• Heavy duty solid cast brass plated support posts
• Designed not to turn in support posts
• Surface Mounted

• 0755-SS-18 – 18″ Length (457 mm)
• 0755-SS-24 – 24″ Length (610 mm)

Model / Series
0755-SS

Type
Towel Bar (Heavy-Duty) – Surface Mounted, Stainless Steel

Dimensions
Available in 18″ and 24″ (457 and 610 mm) lengths.

Overall Dimensions
(variable length”) x 2-5/8″ x 2-1/2″ (variable x 67 x 64 mm)

Towel Bar
1″ (25 mm) O.D. x 20 gauge, type 304 stainless steel

Support Posts
Heavy solid cast brass plated to have stainless steel satin finish to match stainless steel

Mounting
Surface Mounted

• Satin Finish

Stainless steel washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Stainless steel should be protected against muriatic acid, caustic or abrasive materials, and harsh cleaning detergents.

Surface mount each support post to wall with three (3) 1/4″ diameter [Ø6] oval, pan or round head fasteners of length and type to suit wall conditions (supplied by installer) through mounting holes in posts.

To mount on stud walls, provide concealed backing at screw points, secured to studs. Backing must comply with local building codes. If concealed backing is not provided, secure with toggle bolts.

To mount on solid walls, use plastic or fiber type plugs or expansion bolts.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of bar is 48″ [1219] Above Finished Floor (AFF) if clear floor forward reach access is provided or 46″ [1168] AFF if side reach over obstruction is only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0755-SS

• Self-closing door mounted to cabinet with stainless steel spring hinge
• Recessed for side wall installation
• 1.5 gal (5.7 liters) dry solids capacity
• Waste container held in place by “Z” clip retainer
• Safety-edged finger grip provides convenient grip for service
• Door, flanges, waste receptacle and cabinet are 22 gauge type 304 stainless steel alloy 18-8
• Type 304 Stainless Steel - Satin Finish
• Recessed

Model
0473

Type
Sanitary Napkin Disposal – Recessed

Overall Dimensions
13″ x 17-1/4″ x 4-1/4″ (330 x 438 x 108 mm)

Wall Opening
11-1/4″ x 15-3/4″ x 4″ (285 x 400 x 102 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Material Gauge
22 Gauge

Mounting
Recessed

Capacity
1.5 gal (5.7 liters) of dry solids

• Satin Finish

Users push door to deposit waste material. Door is self-closing.

Unit is emptied by removing can and removing disposable waxed waste paper bag which is furnished by others.

Waste container is held in place by a “Z” clip retainer to prevent inadvertent dumping of contents.

Unit is mounted in wall recess using #10 self-threading screws (by others) through concealed mounting holes provided.

Top of rough wall opening is 3/4″ [19] below top of unit.

Rough wall opening required is 11-1/4″ x 15-3/4″ x 4″ minimum.

• Product Care & Maintenance
• Technical Data Sheet – 0473

• Automatic touchless operation
• Dispenses liquid soap or gel hand sanitizer
• Seamless drawn construction
• 22 gauge type 304 stainless steel
• Satin Finish
• Translucent removable tank for easy-to-view content level
• LED indicates function and operational condition
• Powered by 6 AA-size batteries (not included)
• Surface or stand mounted
• 33.8 oz. (1000 ml) capacity

Model
20364

Series
Roval™

Type
Automatic Liquid Soap and Gel Hand Sanitizer Dispenser

Dimensions
5-1/2″ x 10-7/8″ x 4″ (140 x 276 x 102 mm)

Construction
22 gauge Type 304 Stainless Steel

Capacity
33.8 oz. (1000 ml) of liquid soaps and gel hand sanitizer

Power
6 AA-size batteries (not included)

Operation
Automatic – Battery Operated – Touchless

Mounting
Surface or Stand Mounted

Sensor Detection Range
3-1/8″ [80 mm] ± 3/8″ [10 mm]

Dispense Volume
Approximately 0.03 oz. [0.8 ml] per activation

Soap Requirements
Proper usage of this dispenser requires, that only soap/lotion/gel hand sanitizer within the following range for viscosity and pH may be used.

Liquid Soap Viscosity Range (mPa·s or cP)
50 – 3.5k

Gel Hand Sanitizer Viscosity Range (mPa·s or cP)
3.5k – 23k

pH Range
5.5 ~ 8.5

• Satin Finish

Unit operates when an object is positioned within the sensing distance below the dispenser. A measured amount of product is pumped from the nozzle for each activation while battery charge is adequate and appropriate viscosity soap or sanitizer is present in the tank.

Locking door provides security and vandal resistance after soap refill and battery replacement.

Use clean product from a closed container when refilling the reservoir. Clean the soap reservoir of residue on a monthly basis before refilling with fresh product.

Clean the exterior housing regularly with a soft cleaning cloth. Do not soak or submerge the unit and do not clean under running water.

The sensor lens may be cleaned with a soft clean cloth lightly dampened with a suitable general-purpose surface cleaner. Avoid abrasive materials that may scratch the sensor lens.

Replace the batteries at intervals appropriate for the level of use and facility maintenance schedule.

Secure concealed base plate to wall using four suitable self-threading screws through the mounting holes provided and appropriate wall anchors or another suitable mounting system.

For compliance with 2010 ADA Accessibility Standards, install unit so that bottom of unit is 48″ [1219 mm] maximum Above Finished Floor (AFF).

Minimum distance to counter top is 12″ [305 mm].

Install six (6) AA-size 1.5V batteries according to the polarity indication in the concealed battery compartment. Fill tank with appropriate viscosity soap or sanitizer to the correct level and lock the door.

For wall installation, ensure the mounting surface is smooth, flat, vertical and clean, with sufficient clearance above the unit for servicing and lock access.

• Product Care & Maintenance
• Soap & Hand Sanitizer Dispensing Chart
• Owner's Manual – 20364
• Mounting Template – 20364
• Technical Data Sheet – 20364

• L Shaped – Left Hand – 33″ (838 mm) Wide – ADA
• Seat folds up when not in use
• Requires only one hand operation to manually lower to horizontal position for use or raise for departure and arrival
• White solid phenolic seat with black core
• Frame, support legs, flanges, and bracket are type 304 satin finish stainless steel
• Phenolic seat ONLY is field reversible
• Seat is slotted for drainage
• Surface Mounted
• Supports loads up to 500 lbs maximum if installed properly

Model
8206-L

Type
Folding Shower Seat – L Shaped – Left Hand

Seat
½” (13 mm) thick, one piece solid, white colored, black core phenolic

Width
33″ (838 mm)

Projection
22-7⁄8″ (581 mm) from wall

Fold Down Dimensions
33″ x 17″ x 22-7/8″ (838 x 432 x 581 mm)

Fold Up Dimensions
33″ x 35-3/8″ x 22-7/8″ (457 x 899 x 581 mm)

Frame Construction
Type 304 Stainless Steel – Satin Finish

Mounting
Surface Mounted

Compliance
ADA

Supports loads up to 500 lbs maximum if installed properly.

• Seat: White Phenolic with Black Core
• Frame / Body: Type 304 Stainless Steel – Satin Finish

Fold-up Shower Seat requires only one hand operation to manually lower to horizontal position for use or raise for departure and arrival.

Guide bracket with spring detent prevents seat from dropping and provides positive support in usage position as well as spring locked storage position.

This unit is surface mounted. Installer/contractor must provide concealed anchor plate or blocking as specified in construction documents or as required by local building codes prior to wall finishing.

Fasten unit flanges and guide bracket to concealed anchor or blocking plate with appropriate hardware.

Concealed mounting plates or anchors and hardware are not supplied with this product and must be specified separately.

Ensure that mounting configuration complies with local building codes.

• Product Care & Maintenance
• Technical Data Sheet – 8206-L