ASI - 0347 Liquid Soap Dispenser – Vertical – Surface Mounted

• Fabricated of 22 gauge stainless steel
• Type 304 Stainless Steel – Matte Black Powder Coated
• Surface mounted
• Pull type operation
• Dispenses 400 C-fold or 525 multi-fold paper towels
• No adjustment or adapters required
• Heavy-duty stainless steel piano hinge
• Tumbler lock helps prevent unauthorized access
• Refill viewer slots indicate towel supply level

Model
0210-41

Type
Matte Black Paper Towel Dispenser (Multi, C-Fold) – Surface Mounted

Dimensions
11-1/8″ x 14-5/8″ x 4″ (282 x 371 x 101 mm)

Construction
Type 304 Stainless Steel

Material Gauge
22 Gauge

Finish
Matte Black Powder Coated

Mounting
Surface Mounted

Operation
Pull Type

Capacity
400 C-Fold or 525 Multi-Fold Paper Towels

Hinge
Heavy-Duty Stainless Steel Piano Hinge

• Matte Black Powder Coated Finish

Towels are self-feeding as withdrawn by hand until supply is depleted.

Unit may be reloaded with a partial load in-place and will continue to feed properly.

Low level of towel supply is indicated from 25% capacity to empty.

Locking door prevents unauthorized access or removal.

Clean accessible matte black powder coated surfaces with a mild liquid soap and wipe dry. Avoid abrasive cleaners or materials that may damage the finish.

Surface mount unit on wall or partition using five #10 self-threading screws (by others) through concealed mounting holes provided.

Four mounting holes through the back are keyhole slots for ease in hanging the unit on pre-installed screws.

Center top mounting hole is a horizontal slot for ease of adjustment and vandal-resistant locking.

For compliance with 2010 ADA Accessibility Standards, install unit so that the centerline of the towel dispenser slot is 48″ (1219 mm) maximum Above Finished Floor (AFF).

• Product Care & Maintenance
• Technical Data Sheet – 0210-41

• Square shaped towel bar
• Fabricated from triple chrome plated rust-resistant Zamak
• 3/4″ (19 mm) square steel tubing
• 21 gauge (.032 in. <.81 mm> wall) tubing
• Triple chrome plated steel tubing
• Surface mounted
• Available in 18″ and 24″ lengths

• 0760-Z-18 – 18″ Length (457 mm)
• 0760-Z-24 – 24″ Length (610 mm)

Model / Series
0760-Z

Type
Towel Bar (Square) – Surface Mounted, Chrome Plated Zamak

Dimensions
18-36″ x 1-7/16″ x 3-3/16″ (457-914 x 37 x 81 mm)

Bar
3/4″ (19 mm) Square, 21 Gauge Steel Tubing

Construction
Chrome Plated Zamak with Triple Chrome Plated Steel Tubing

Mounting
Surface Mounted

• Triple Chrome Plated

Washroom accessory products require regular surface cleaning. As long as a regular cleaning schedule is followed, clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

For general utility, mount bar 50″ (1270 mm) Above Finished Floor (AFF) from center line of towel bar.

Locate wall brackets in appropriate positions and secure wall plates with two (2) self-threading screws (by others) through two slot holes in wall plates.

Install brackets over wall plates and fasten in place with stainless steel set screws through tapped holes in brackets.

• Product Care & Maintenance
• Technical Data Sheet – 0760-Z

• Holds standard core roll paper towels up to 6″ (152 mm) diameter
• Heavy-duty die-cast aluminum construction
• Satin-matte silver-grey finish
• Surface mounted
• Controlled-delivery spindle helps reduce towel waste
• Impact-resistant ABS thermoplastic spindle
• Concealed release mechanism provides theft resistance
• Roll core cannot be removed until paper is exhausted

Model
8165

Series
Traditional™

Type
Paper Towel Holder (Roll-Type) – Surface Mounted

Dimensions
13″ x 1-3/4″ x 4″ Projection (330 x 44 x 102 mm)

Roll Capacity
Standard paper towel roll up to 6″ (152 mm) diameter

Holder Construction
Die-Cast Aluminum

Spindle Construction
Impact-Resistant ABS Thermoplastic

Finish
Satin-Matte Silver-Grey Finish

Mounting
Surface Mounted

Delivery Type
Controlled Delivery

• Satin-Matte Silver-Grey Finish

Spindle revolves 1/2 revolution for each operation and then returns to its original position.

Paper towel roll core prevents access to the release pin and cannot be removed from the spindle until exhausted.

Unit is replenished by releasing a concealed pin which in turn releases a spring lock mechanism on the spindle.

Unit is surface mounted on wall using No. 10 self-tapping screws supplied.

For ADA accessibility, install unit so that roll centerline is 54″ (1372 mm) maximum Above Finished Floor (AFF) where clear floor side reach access is provided.

Where clear floor forward reach access is provided, roll centerline should be 48″ (1219 mm) maximum AFF.

Where side reach over an obstruction such as a vanity is provided, roll centerline should be 46″ (1168 mm) maximum AFF.

• Product Care & Maintenance
• Technical Data Sheet – 8165

• Frame, waste receptacle and cabinet fabricated of 22 gauge stainless steel alloy 18-8, type 304
• Waste receptacle has hemmed edges for safety
• Internal hooks for hanging a reusable vinyl bag
• Optional reusable vinyl bag model 58-PY for 12 gal unit
• Tumbler lock retains waste receptacle
• Container locks into cabinet and is removable for servicing
• Available in multiple projection, recess, mounting and capacity configurations
• Type 304 Stainless Steel - Satin Finish

Series
0458 Series

Type
Traditional™ Waste Receptacle

Overall Dimensions
17-1/4″ x 30-1/2″ x 8″ (438 x 775 x 203 mm)

Wall Opening
15-3/4″ x 29″ x (variable*) (400 x 737 mm)

Standard Model Capacity
12 gal (46 liters)

Construction
22 gauge stainless steel alloy 18-8, Type 304

Finish
Satin Finish

Mounting
Semi-Recessed or Surface Mounted, depending on selected configuration

• Satin Finish

Waste receptacle is emptied manually on cycle determined by maintenance requirements.

Optional reusable liner bags may be purchased to hang on internal hooks or disposable bags may be draped over rim and held in place when receptacle is locked into cabinet.

Keyed tumbler lock prevents unauthorized removal.

Container locks into cabinet and is removable for servicing.

Mount unit in wall recess using #10 self-threading screws through concealed mounting holes provided.

Top of Rough Wall Opening (RWO) is 3/4″ (19 mm) below top of unit.

Wall opening for the standard configuration is 15-3/4″ x 29″ with depth varying according to the selected configuration.

Select the appropriate model according to the required projection, recess depth, mounting method and waste capacity.

• Product Care & Maintenance
• Technical Data Sheet – 0458 Series