Products

• Fabricated of 22 gauge stainless steel
• Type 304 Stainless Steel – Matte Black Powder Coated
• Surface mounted
• Pull type operation
• Dispenses 400 C-fold or 525 multi-fold paper towels
• No adjustment or adapters required
• Heavy-duty stainless steel piano hinge
• Tumbler lock helps prevent unauthorized access
• Refill viewer slots indicate towel supply level

Model
0210-41

Type
Matte Black Paper Towel Dispenser (Multi, C-Fold) – Surface Mounted

Dimensions
11-1/8″ x 14-5/8″ x 4″ (282 x 371 x 101 mm)

Construction
Type 304 Stainless Steel

Material Gauge
22 Gauge

Finish
Matte Black Powder Coated

Mounting
Surface Mounted

Operation
Pull Type

Capacity
400 C-Fold or 525 Multi-Fold Paper Towels

Hinge
Heavy-Duty Stainless Steel Piano Hinge

• Matte Black Powder Coated Finish

Towels are self-feeding as withdrawn by hand until supply is depleted.

Unit may be reloaded with a partial load in-place and will continue to feed properly.

Low level of towel supply is indicated from 25% capacity to empty.

Locking door prevents unauthorized access or removal.

Clean accessible matte black powder coated surfaces with a mild liquid soap and wipe dry. Avoid abrasive cleaners or materials that may damage the finish.

Surface mount unit on wall or partition using five #10 self-threading screws (by others) through concealed mounting holes provided.

Four mounting holes through the back are keyhole slots for ease in hanging the unit on pre-installed screws.

Center top mounting hole is a horizontal slot for ease of adjustment and vandal-resistant locking.

For compliance with 2010 ADA Accessibility Standards, install unit so that the centerline of the towel dispenser slot is 48″ (1219 mm) maximum Above Finished Floor (AFF).

• Product Care & Maintenance
• Technical Data Sheet – 0210-41

• Frame, waste receptacle and cabinet fabricated of 22 gauge stainless steel alloy 18-8, type 304
• Waste receptacle has hemmed edges for safety
• Internal hooks for hanging a reusable vinyl bag
• Optional reusable vinyl bag model 58-PY for 12 gal unit
• Tumbler lock retains waste receptacle
• Container locks into cabinet and is removable for servicing
• Available in multiple projection, recess, mounting and capacity configurations
• Type 304 Stainless Steel - Satin Finish

Series
0458 Series

Type
Traditional™ Waste Receptacle

Overall Dimensions
17-1/4″ x 30-1/2″ x 8″ (438 x 775 x 203 mm)

Wall Opening
15-3/4″ x 29″ x (variable*) (400 x 737 mm)

Standard Model Capacity
12 gal (46 liters)

Construction
22 gauge stainless steel alloy 18-8, Type 304

Finish
Satin Finish

Mounting
Semi-Recessed or Surface Mounted, depending on selected configuration

• Satin Finish

Waste receptacle is emptied manually on cycle determined by maintenance requirements.

Optional reusable liner bags may be purchased to hang on internal hooks or disposable bags may be draped over rim and held in place when receptacle is locked into cabinet.

Keyed tumbler lock prevents unauthorized removal.

Container locks into cabinet and is removable for servicing.

Mount unit in wall recess using #10 self-threading screws through concealed mounting holes provided.

Top of Rough Wall Opening (RWO) is 3/4″ (19 mm) below top of unit.

Wall opening for the standard configuration is 15-3/4″ x 29″ with depth varying according to the selected configuration.

Select the appropriate model according to the required projection, recess depth, mounting method and waste capacity.

• Product Care & Maintenance
• Technical Data Sheet – 0458 Series

• Square shaped towel bar
• Fabricated from triple chrome plated rust-resistant Zamak
• 3/4″ (19 mm) square steel tubing
• 21 gauge (.032 in. <.81 mm> wall) tubing
• Triple chrome plated steel tubing
• Surface mounted
• Available in 18″ and 24″ lengths

• 0760-Z-18 – 18″ Length (457 mm)
• 0760-Z-24 – 24″ Length (610 mm)

Model / Series
0760-Z

Type
Towel Bar (Square) – Surface Mounted, Chrome Plated Zamak

Dimensions
18-36″ x 1-7/16″ x 3-3/16″ (457-914 x 37 x 81 mm)

Bar
3/4″ (19 mm) Square, 21 Gauge Steel Tubing

Construction
Chrome Plated Zamak with Triple Chrome Plated Steel Tubing

Mounting
Surface Mounted

• Triple Chrome Plated

Washroom accessory products require regular surface cleaning. As long as a regular cleaning schedule is followed, clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

For general utility, mount bar 50″ (1270 mm) Above Finished Floor (AFF) from center line of towel bar.

Locate wall brackets in appropriate positions and secure wall plates with two (2) self-threading screws (by others) through two slot holes in wall plates.

Install brackets over wall plates and fasten in place with stainless steel set screws through tapped holes in brackets.

• Product Care & Maintenance
• Technical Data Sheet – 0760-Z

• Dispenses 250 seat covers
• 20 gauge type 304 stainless steel construction
• Satin finish
• Surface mounted
• Curved front adds strength and elegance
• Concealed, multi-staked piano hinge
• Covers are self-feeding until supply is depleted
• Concealed bottom opening allows manual reloading

Model
20477-SM

Series
Roval™

Type
Surface Mounted Toilet Seat Cover Dispenser

Dimensions
15-3/4″ x 11″ x 2-3/8″ (400 x 280 x 60 mm)

Construction
20 gauge Type 304 Stainless Steel

Finish
Satin Finish

Mounting
Surface Mounted

Capacity
Dispenses 250 seat covers

Hinge
Concealed, Multi-Staked Piano Hinge

• Satin Finish

Covers are self-feeding until supply is depleted. Unit is manually reloaded with a full box through concealed opening in bottom on schedule determined by maintenance requirements.

Regularly inspect and replenish the supply of toilet seat covers according to facility maintenance requirements.

Clean stainless steel surfaces regularly with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Mount unit on wall or partition surface using two (2) #10 x 1-1/4″ [32] self-threading flat head screws (by others).

Mounting holes are accessible through the dispenser slot during installation and are concealed behind the dispenser box after the dispensing product is loaded for vandal-resistant installation.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of dispenser slot is 48″ [1219] maximum Above Finished Floor (AFF) if clear floor access is provided.

Where only side reach over an obstruction is provided, such as over a vanity, centerline of dispenser slot should be 46″ [1168] maximum AFF.

• Product Care & Maintenance
• Technical Data Sheet – 20477-SM

• Straight grab bar
• Snap Flange – cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel – Matte Black Powder Coated
• Smooth surface
• Surface mounted
• 18 gauge tubing with 1-1/2″ Outside Diameter (38 mm)
• Available in 18″, 24″, 36″, 42″ and 48″ lengths
• 1-1/2″ (38 mm) wall clearance

• 3801-18-41 – 18″ Length (457 mm)
• 3801-24-41 – 24″ Length (610 mm)
• 3801-36-41 – 36″ Length (914 mm)
• 3801-42-41 – 42″ Length (1067 mm)
• 3801-48-41 – 48″ Length (1219 mm)

Series
3801-41 Series

Type
Straight Snap Flange Grab Bar

Available Lengths
18″ (457 mm), 24″ (610 mm), 36″ (914 mm), 42″ (1067 mm), 48″ (1219 mm)

Outside Diameter
1-1/2″ (38 mm)

Tubing
18 Gauge Type 304 Stainless Steel

Surface
Smooth

Mounting Flange
3-1/8″ (79 mm) O.D., 1/8″ (3 mm) thick Type 304 stainless steel with 2 screw holes and 3 locking dimples

Snap-On Cover
22 gauge Type 304 stainless steel, 3-3/16″ (81 mm) diameter

Wall Clearance
1-1/2″ (38 mm)

Mounting
Surface Mounted

Capacity
Designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 requirements for a load in excess of 250 lbs (113.4 kg) when properly mounted

• Matte Black Powder Coated Finish

All accessible Matte Black Powder Coated surfaces should be cleaned with a mild liquid soap only. The surfaces should then be wiped and dried.

In areas containing showers, the accessories must receive ventilation from the outside so that excess humidity can escape.

Do not use abrasive powders or scouring pads, water closet cleaners, ceramic tile cleaners, solutions containing more than 1% ammonia by volume, solutions containing acids or lye, or solutions containing enzymes.

Use grab bar as a template to mark mounting hole locations and pre-drill holes.

Install bar using two (2) #10 self-threading flat head or oval head screws (by others), or other suitable fastener system (by others), for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on architectural plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards, install unit so that the top of the grab bar is 33″ (840 mm) minimum Above Finished Floor (AFF) to 36″ (915 mm) maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled.

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 3801-18-41 – 18″
• Technical Data Sheet – 3801-24-41 – 24″
• Technical Data Sheet – 3801-36-41 – 36″
• Technical Data Sheet – 3801-42-41 – 42″
• Technical Data Sheet – 3801-48-41 – 48″

• Single Hook
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• Hook extends 2" [51] from wall
• Hook is suitable for a robe or clothing and small carry bags

Model
7340-S

Type
Robe Hook (Single)

Dimensions
2" [51] W x 2" [51] H x 2" [51] D

Construction
Type 304 Stainless Steel - Satin Finish

Mounting
Surface Mounted

• 7340-B – Bright Finish
• 7340-S – Satin Finish

Hook is suitable for a robe or clothing and small carry bags.

Surface mount unit on door back or wall using two (2) #10 self-threading screws (by others) through holes provided in mounting plate into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit door or wall conditions.

Hang post and flange assembly on mounting plate and tighten set screw to lock unit to plate.

For compliance with ICC/ANSI A-117.1-2003 and 2010 ADA Accessibility Standards, install unit with top of hook 48" [1219] maximum Above Finished Floor (AFF) or 46" [1168] max AFF if side reach access over an obstruction (e.g. vanity) with reach depth greater than 10" [254] and less than 25" [635] is only provided or 44" [1118] max AFF if forward reach over an obstruction with reach depth greater than 20" [508] and less than 25" [635] is only provided.

For general utility, install hook with centerline of mounting plate 68" [1727] AFF.

• Product Care & Maintenance
• Technical Data Sheet – 7340-S
• Technical Data Sheet – 7340-B

• Holds standard core roll paper towels up to 6″ (152 mm) diameter
• Heavy-duty die-cast aluminum construction
• Satin-matte silver-grey finish
• Surface mounted
• Controlled-delivery spindle helps reduce towel waste
• Impact-resistant ABS thermoplastic spindle
• Concealed release mechanism provides theft resistance
• Roll core cannot be removed until paper is exhausted

Model
8165

Series
Traditional™

Type
Paper Towel Holder (Roll-Type) – Surface Mounted

Dimensions
13″ x 1-3/4″ x 4″ Projection (330 x 44 x 102 mm)

Roll Capacity
Standard paper towel roll up to 6″ (152 mm) diameter

Holder Construction
Die-Cast Aluminum

Spindle Construction
Impact-Resistant ABS Thermoplastic

Finish
Satin-Matte Silver-Grey Finish

Mounting
Surface Mounted

Delivery Type
Controlled Delivery

• Satin-Matte Silver-Grey Finish

Spindle revolves 1/2 revolution for each operation and then returns to its original position.

Paper towel roll core prevents access to the release pin and cannot be removed from the spindle until exhausted.

Unit is replenished by releasing a concealed pin which in turn releases a spring lock mechanism on the spindle.

Unit is surface mounted on wall using No. 10 self-tapping screws supplied.

For ADA accessibility, install unit so that roll centerline is 54″ (1372 mm) maximum Above Finished Floor (AFF) where clear floor side reach access is provided.

Where clear floor forward reach access is provided, roll centerline should be 48″ (1219 mm) maximum AFF.

Where side reach over an obstruction such as a vanity is provided, roll centerline should be 46″ (1168 mm) maximum AFF.

• Product Care & Maintenance
• Technical Data Sheet – 8165

• Horizontal baby changing station
• Recessed mounting
• Type 304 stainless steel door facing and collar
• Available in Satin Finish or Matte Black Powder Coated finish
• Unit complies with 2010 ADA Accessibility Standards
• Intended use for infants up to 3.5 years old and up to 50 lbs (23kg)
• Bed is designed to cradle a child’s body
• Adjustable two-part vinyl-coated safety strap with Sure-Lock latch
• Integral bag hook
• Bed-liner dispenser convertible to a multi-fold towel dispenser
• Damped gas spring aids one-handed operation using less than 5 lbs force (22.2N)

Series
9018 Series

Models
9018 / 9018-41

Type
Baby Changing Station, HORIZONTAL – STAINLESS STEEL, Recessed

Closed Dimensions
39-5⁄32″ x 28-1/4″ x 3⁄8″ (995 x 718 x 10 mm)

Open Dimensions
39-5/32” x 28-1/4” x 18-1/8” (995 x 718 x 460 mm)

Wall Opening
35-1/2″ x 24-1/2″ x 4″ min (902 x 622 x 102 mm)

Construction
Type 304 Stainless Steel

Mounting
Recessed

9018 Finish
Satin Finish

9018-41 Finish
Matte Black Powder Coated

Intended Use
Infants up to 3.5 years old and up to 50 lbs (23kg)

Static Load Testing
Tested during development to sustain 250 lbs (113 kg) static load with minimal deflection.

• 9018 – Type 304 Stainless Steel - Satin Finish
• 9018-41 – Type 304 Stainless Steel - Matte Black Powder Coated

• Complies with 2010 ADA Accessibility Standards
• ASTM F-2285 & F-2388 compliant
• G-21 and G-22 compliant
• ANSI Z535 compliant
• ANSI 117.1 compliant
• EN 12221-1 and EN 12221-2 compliant
• Adjustable two-part vinyl-coated safety strap with Sure-Lock latch
• Operable using less than 5 lbs force (22.2N)

Unit platform is shaped to keep a child restrained from rolling out of the bed. Unit is easily opened and closed by user with one hand in any location and handle cavity is provided on door face for preferred use.

Unit is operable with less than 5 Lbf (22.2N) while not requiring any tight grasping, pinching or twisting of the wrist.

Bed liner/towel dispenser presents liners or towels for user hygiene and convenience. Dispenser lid is provided for sanitary protection and ease of loading of wipes or liners.

Safety strap is easily adjustable by user for baby size and Sure-Lock latch securely resists opening until released by opposing finger pressure by adult caretaker/parent.

Liners/towels are easily replenished by service personnel as required.

Unit is recess mounted using hardware supplied through concealed mounting holes. The supplied hardware kit contains fasteners suitable for metal or wood stud walls in dry locations and general hollow wall construction where adequate substrate strength is obtained.

Fasteners and anchors for masonry walls are not provided. Wall reinforcement must be suitable to sustain transfer of maximum unit loading.

Mounting hole plug covers are supplied to conceal fasteners after installation.

Provide Rough Wall Opening (RWO) of required depth from face of finished wall. Mount unit in properly framed RWO using four (4) #10 x 1-1/2″ [M5 x 38] self-threading pan head screws through side holes.

Alternate rear-hole mounting may be used where wall depth and framing reinforcement permits, using suitable fasteners appropriate for wall conditions.

Rough Wall Opening (RWO) required is 35-1/2″ W x 24-1/2″ H x 4″ D minimum [902 x 622 x 102].

• Product Care & Maintenance
• Installation, Maintenance & Operation Owner's Manual – 9018 Series
• Technical Data Sheet – 9018 – Satin Finish
• Technical Data Sheet – 9018-41 – Matte Black

• Satin finish stainless steel construction
• Type 304 stainless steel
• Robust 16 gauge stainless steel face
• Curved radius edges
• Surface mounted
• 48 fl. oz. (1.4 L) capacity
• All-purpose valve dispenses liquid, lotion and detergent-type soaps
• Tamper-resistant refill window with concealed fastening
• Vandal-resistant hinged filler-top
• 3/16″ concealed piano hinge adds durability

Model
9343

Series
Profile™

Type
Liquid Soap Dispenser – Surface Mounted

Dimensions
7-1/4” x 6-1/2” x 3-11/16” (184 x 165 x 94 mm)

Spout Projection
15/16” (24 mm)

Capacity
48 fl. oz. (1.4 L)

Construction
Type 304 Stainless Steel

Mounting
Surface Mounted

Dispensing
Manual push-button operation

Soap Requirements
Proper usage of this dispenser requires, that only soap within the following range for viscosity and pH may be used.

Viscosity Range (mPa·s or cP)
100 – 2.5k

pH Range
5.5 ~ 8.0

Consumable Type
Liquid Soap

• Satin Finish

Soap is manually dispensed by depressing the push button. Unit is refilled through the hinged door at the top requiring the special key supplied to open.

Soap tank will continue to feed properly until empty. Tank supply is replenished manually according to maintenance needs.

Under normal usage, stainless steel products require regular cleaning with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Soap dispenser valves in low-traffic areas should be wiped regularly to remove air-hardened soap residue from the nozzle spout.

If the dispenser fails to operate because of dried soap or debris, the dispenser may be removed from the wall plate and flushed with hot water as described in the ASI installation and maintenance instructions.

Unit is surface mounted to wall or partition by means of a wall mounting plate and screws. Unit is secured to the mounting plate and locked in place by means of a locking screw installed through the tamper-resistant refill door.

Recommended mounting height for general utility is 42″ (1067 mm) Above Finished Floor (AFF) or 6″ (152 mm) minimum above the wash basin to bottom of unit.

Allow 4″ (102 mm) minimum clearance above the unit for filling.

Mount wall plate vertically with the wide part of the “V” at the top. Use suitable mounting hardware for the wall construction.

Unlock the filler door using the special service key furnished, position the dispenser on the wall plate, press the tank down firmly, and tighten the internal locking screw securely.

For maximum usability and ADA accessibility, the valve may be installed at a maximum of 54″ (1372 mm) AFF for clear-floor side reach, 48″ (1219 mm) AFF for clear-floor forward reach, or 46″ (1168 mm) AFF where side reach over an obstruction is provided.

• Product Care & Maintenance
• Soap & Hand Sanitizer Dispensing Chart
• Installation & Maintenance Instructions – 9343
• Technical Data Sheet – 9343