ASI - 8206-L Folding Shower Seat, Solid Phenolic, White – L Shaped, 33″ Wide – Left Hand, ADA

• Horizontal baby changing station
• 100% high-density polyethylene construction
• Surface Mounted
• Low profile – only 4″ (102 mm) deep when closed
• Designed to support an infant up to 3.5 years old and up to 50 lbs (23 kg)
• Bed is shaped to cradle a child’s body
• Easy one-handed operation
• Adjustable two-part safety strap with Sure-Lock latch
• Two integral bag hooks
• Bed-liner dispenser convertible to a multi-fold towel dispenser
• Damped gas spring aids one-handed operation

Model
9012

Type
Baby Changing Station, HORIZONTAL – PLASTIC

Closed Dimensions
36” x 22” x 4” (914 x 559 x 102 mm)

Open Dimensions
36” x 22” x 20-7/16” (914 x 559 x 519 mm)

Construction
High-Density Polyethylene (HDPE)

Mounting
Surface Mounted

Intended Use
Infants up to 3.5 years old and up to 50 lbs (23 kg)

• ADA compliant
• ASTM F-2285 & F-2388 compliant
• ANSI Z535 compliant
• ANSI 117.1 compliant
• Adjustable safety strap with Sure-Lock latch
• Operable with less than 5 lbs force (22.2N)
• No tight grasping, pinching or twisting of the wrist is required for operation

Unit platform is shaped to cradle a child’s body. Unit is easily opened and closed by user with one hand anywhere on top or front edge of bed or using bag hooks/hand grips on sides.

Bed liner/towel dispenser presents liners or towels for user hygiene and convenience. Dispenser lip retains stack for single liner/towel dispensing.

Safety strap is easily adjustable by user for baby size and Sure-Lock latch securely resists opening until released by opposing finger pressure by adult caretaker.

Ensure that the liner compartment is adequately stocked. Thoroughly clean the unit daily with warm water and mild anti-bacterial detergent, rinse with clean water and dry. Do not use abrasive cleaning agents.

Periodically inspect the unit to ensure that it remains securely attached to the wall and that the unit and wall mounting have not been affected by vandalism or abnormal wear.

Surface mount unit using hardware supplied through recessed mounting holes provided. Hardware kit supplied has fasteners suitable for metal or wood stud walls in dry locations and general hollow wall construction where adequate substrate strength is obtained.

Fasteners and anchors for masonry walls are not provided. Wall reinforcement must be suitable to sustain transfer of maximum unit loading.

Locate wall studs at 16″ (406 mm) O.C. for fastening the station. If two wall studs cannot be used, use two screws into one stud and install suitable toggle fasteners securely at the non-stud location.

Attach unit to wall studs with four 1/4″ x 3″ long Philips pan head self-threading screws with flat washers. Where wall studs are not available, attach with four 1/4″-20 x 3″ toggle bolts with flat washers into toggles or expansion nuts.

Installation should be performed by a qualified technician, and the wall and attachment method must be strong enough to support the rated load.

• Product Care & Maintenance
• Installation & Maintenance Instructions – 9012
• Technical Data Sheet – 9012

• Curved front adds strength and elegance
• Cabinet front is formed seamless
• 22 gauge type 304 stainless steel alloy 18-8
• Concealed, multi-staked piano hinge
• Removable waste can
• Full top edge is hemmed with return to inside for user and service safety
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• 1 gal. (3.8 L) capacity

Model
20852

Series
Roval™

Type
Surface Mounted Sanitary Waste Receptacle

Dimensions
7-1/4″ x 10″ x 3-1/2″ (185 x 253 x 89 mm)

Construction
22 gauge type 304 stainless steel alloy 18-8

Capacity
1 gal. (3.8 L)

Mounting
Surface Mounted

• Satin Finish

User lifts lid to deposit waste material. Maintenance schedule determines trash removal cycle. Unload unit by either removing the disposable wax paper liner bag (by others) or unhooking the unit from the mounting screws and inverting to empty into appropriate bulk collection container.

For general utility mount the receptacle 28″ [711] to 40″ [1016] above finished floor (AFF) from top of unit.

For compliance with 2010 ADA Accessibility Standards install unit so that top cover is no higher than 48″ [1219] above finished floor.

Hang unit on wall with two (2) pre-installed #10 x 1-1/4″ [32] self-threading pan head screws (by others) through the mounting keyhole slots provided into suitable wall reinforcements (by others) or two (2) pre-installed #10 x 3/4″ [19] self-threading pan head screws (by others) through the mounting keyhole slots provided into metal partition.

Surface mounting collars conveniently adapt standard recessed mounting cabinets for use on walls with insufficient depth for recessing or wall materials that would make cutouts impossible.

• Product Care & Maintenance
• Surface Mounting Collar Installation
• Technical Data Sheet – 20852

• 1″ diameter (Ø25) bar
• 20 gauge tubing
• Type 304 Stainless Steel - Satin Finish
• Length will be as specified
• Wall Mounted
• Rod is held captive by flanges (#1214-1, sold separately) when installed properly
• Curtain hooks Model 1200-SHU may be used with the rod

• 24″ (610 mm)
• 30″ (762 mm)
• 36″ (914 mm)
• 42″ (1067 mm)
• 48″ (1219 mm)
• 54″ (1372 mm)
• 60″ (1524 mm)
• 66″ (1676 mm)
• 72″ (1829 mm)

Maximum rod length is 120″ (3048 mm). Rods longer than 72″ (1829 mm) require ceiling hanger Model #1224-C18.

Model
1214-2

Type
Shower Curtain Rod – 1″ dia. Bar, Stainless Steel

Diameter
1″ (Ø25)

Tubing
20 gauge

Construction
Type 304 Stainless Steel

Maximum Length
120″ (3048 mm)

Mounting
Wall Mounted

Flanges
#1214-1, sold separately

• Satin Finish

Rod is held captive by flanges (#1214-1, sold separately) when installed properly. Rod may rotate in flanges if turned by hand.

Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others.

Rod will bend and pull from flanges if significant body weight is suspended.

Install rod in straight section between two (2) mounting flanges with no more than 1/4″ [6] total wall clearance.

Rods longer than 72″ [1829] require ceiling hanger Model #1224-C18.

For use with standard shower curtain Model #1200 or #1200-V having 72″ [1829] length and standard hooks (Model #1200-SHU), install unit with rod centerline 74-1/2″ [1892] maximum above finished floor (MAX AFF) or 67″ [1702] above tub rim to obtain 6″ [152] bottom overlap.

Seal screw holes in walls under flange to prevent any sprayed water from possibly infiltrating the wall structure.

• Product Care & Maintenance
• Technical Data Sheet – 1214-2

• Roll formed, interlocking frame with heliarc welded corners
• Corners are ground and polished smooth to a uniform satin finish
• Type 304 stainless steel frame
• Concealed hanging bracket
• Tamper-proof set screws lock onto top and bottom of frame
• One-piece back plate with theft-resistant locking device
• Surface Mounted
• Various sizes and reflective surfaces available

Plate Glass

• 0600-1620 – 16” wide x 20” high (406 x 508 mm)
• 0600-1624 – 16” wide x 24” high (406 x 610 mm)
• 0600-1630 – 16” wide x 30” high (406 x 762 mm)
• 0600-1824 – 18” wide x 24” high (457 x 610 mm)
• 0600-1830 – 18” wide x 30” high (457 x 762 mm)
• 0600-1836 – 18” wide x 36” high (457 x 914 mm)
• 0600-2060 – 20” wide x 60” high (508 x 1524 mm)
• 0600-2430 – 24” wide x 30” high (610 x 762 mm)
• 0600-2436 – 24” wide x 36” high (610 x 914 mm)
• 0600-2442 – 24” wide x 42” high (610 x 1067 mm)
• 0600-2448 – 24” wide x 48” high (610 x 1219 mm)
• 0600-2460 – 24” wide x 60” high (610 x 1524 mm)
• 0600-2472 – 24” wide x 72” high (610 x 1829 mm)
• 0600-3036 – 30” wide x 36” high (610 x 914 mm)
• 0600-3636 – 36” wide x 36” high (914 x 914 mm)
• 0600-3648 – 36” wide x 48” high (914 x 1219 mm)
• 0600-4830 – 48” wide x 30” high (1219 x 762 mm)
• 0600-4836 – 48” wide x 36” high (1219 x 914 mm)
• 0600-6036 – 60” wide x 36” high (1524 x 914 mm)
• 0600-7236 – 72” wide x 36” high (1829 x 914 mm)

Tempered Glass

• 0600-B1824 – 18” wide x 24” high (457 x 610 mm)
• 0600-B1830 – 18” wide x 30” high (457 x 762 mm)
• 0600-B1836 – 18” wide x 36” high (457 x 914 mm)
• 0600-B2430 – 24” wide x 30” high (610 x 762 mm)
• 0600-B2436 – 24” wide x 36” high (610 x 914 mm)
• 0600-B2448 – 24” wide x 48” high (610 x 1219 mm)
• 0600-B2460 – 24” wide x 60” high (610 x 1524 mm)
• 0600-B2472 – 24” wide x 72” high (610 x 1829 mm)

Stainless Steel, Type 304 with #8 Finish

• 0600-C1418 – 14” wide x 18” high (356 x 457 mm)
• 0600-C1824 – 18” wide x 24” high (457 x 610 mm)
• 0600-C1830 – 18” wide x 30” high (457 x 762 mm)
• 0600-C2430 – 24” wide x 30” high (610 x 762 mm)
• 0600-C2436 – 24” wide x 36” high (610 x 914 mm)
• 0600-C2460 – 24” wide x 60” high (610 x 1524 mm)

Series
0600 Series

Type
Stainless Steel Inter-Lok Angle Frame Mirror

Frame
3⁄4″ x 5⁄8″ (19 x 16 mm) roll formed 18 gauge type 304 stainless steel angle

Frame Finish
Uniform satin finish

Construction
Type 304 stainless steel

Mounting
Surface Mounted

Reflective Surface Options
Plate Glass, Tempered Glass, and Stainless Steel Type 304 with #8 Finish

Back Plate
One piece, attached to frame with theft-resistant locking device

Plate Glass
#1 quality polished plate glass with silver coating and protective copper plating. Image quality: BEST.

Tempered Glass
1/4″ (6.4 mm) polished tempered glass with silver coating. Image quality: BETTER.

Stainless Steel with #8 Finish
Type 304 stainless steel polished to a #8 mirror finish. Image quality: FAIR.

Reflective quality may vary by surface type, and the likelihood of distortion increases as reflective surface size increases.

• Frame: Type 304 Stainless Steel - Satin Finish
• Reflective Surface: Plate Glass
• Reflective Surface: Tempered Glass
• Reflective Surface: Type 304 Stainless Steel with #8 Finish

Install bracket level and plumb as per diagram location using #10 self-threading screws (by others).

Hang mirror on bracket and tighten locking screws at top and bottom.

For compliance with 2010 ADA Accessibility Standards and 2015 ABA Standards, bottom edge of reflecting surface should be no higher than 40″ [1016] Above Finished Floor.

• Product Care & Maintenance
• Mirror Size Options Chart
• Technical Data Sheet – 0600 Series