ASI - 7305-S Toilet Tissue Holder (Single) – Surface Mounted

• Straight Grab Bar
• Snap Flange - cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Smooth surface
• Surface Mounted
• 18 gauge tubing with 1-1/4″ Outside Diameter [Ø32]
• Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples
• Mounting flange is 1/8″ (3 mm) thick, type 304 stainless steel
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter

• 18″ (457 mm) – 3701-18
• 36″ (914 mm) – 3701-36
• 42″ (1067 mm) – 3701-42

Series
3701 Series

Type
Straight Grab Bar

Tubing
18 gauge tubing with 1-1/4″ Outside Diameter [Ø32]

Construction
Type 304 Stainless Steel - Satin Finish

Surface
Smooth

Mounting
Surface Mounted

Wall Clearance
1-1/2″ [38]

Mounting Flange
Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples; 1/8″ (3 mm) thick, type 304 stainless steel.

Cover
Type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter.

ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 that fabricated product shall be of adequate strength to support a load in excess of 250 pounds (113.4 kg). Mounting to the wall is a critical part of the system to meet this requirement. The fastener system must be adequately sized to withstand the shear, tension or pullout, and torsion loads generated by the maximum loading.

• Satin Finish

Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using two (2) #10 self-threading flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33″ [840] minimum Above Finished Floor (AFF) to 36″ [915] maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series).

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 3701-18
• Technical Data Sheet – 3701-36
• Technical Data Sheet – 3701-42

• Low Profile - Twin Jumbo Roll Dispenser
• Holds two 9″ (229 mm) diameter rolls
• Accommodates 2-1⁄4″ or 3″ (57 or 76 mm) diameter cores
• Slide panel exposes other roll when one roll is depleted
• Door cabinet and mounting plate fabricated of 18 gauge type 304 stainless steel with a satin finish
• Heavy-duty stainless steel pivot hinges
• Equipped with tumbler lock
• Viewing slot provides easy visual indication of remaining tissue supply
• Surface Mounted

Model
0039

Type
Low Profile 9″ Jumbo Roll Toilet Tissue Dispenser

Dimensions
20-1⁄2″ x 11-3⁄16″ x 4-11⁄16″ (521 x 284 x 119 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Cabinet & Mounting Plate
18 gauge Type 304 stainless steel

Mounting
Surface Mounted

Capacity
Holds two 9″ (229 mm) diameter rolls

Core Sizes
2-1⁄4″ or 3″ (57 or 76 mm) diameter core

• Type 304 Stainless Steel - Satin Finish

Two (2) 9″ [Ø229] outside diameter jumbo rolls of toilet tissue are mounted over 3″ [Ø76] inside diameter (ID) core adapters. Two (2) 2-1/4″ [Ø57] ID core rolls may be used by removing the core adapters.

Whenever one roll of toilet tissue is depleted, the other roll is selected by shifting over the lever at the bottom of the unit.

Viewing slot continuously reveals tissue level. Key and locked door prevents unauthorized access or removal. Tissue supply is replenished on a cycle determined by maintenance needs.

Surface mount unit for general utility within 12″ [305] of front of toilet from centerline and 31″ [787] above finished floor (AFF) from bottom of unit with five (5) No. 12 x 3/4″ [Ø5.5 x 20] pan head self threading screws (by others), or other types as more suitable to site conditions (by others), including wall type appropriate anchors (by others) as may be required through mounting holes provided.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of nearest roll is between 7″ to 9″ [178 to 229] from front of commode and centerline of rolls is 19″ [483] minimum AFF to 44″ [1118] max AFF.

• Product Care & Maintenance
• Technical Data Sheet – 0039

• Dispenses 250 single or half-fold seat covers
• Fabricated of 22 gauge type 304 stainless steel with satin finish
• Heavy-duty 3/16″ Dia. [Ø4.8] stainless steel multi-staked piano hinged door
• Door includes tumbler lock
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted

Model
0477-SM

Type
Toilet Seat Cover Dispenser – Surface Mounted

Dimensions
15-3/4” x 11” x 1-7/8” (400 x 279 x 48 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Cabinet
22 gauge

Mounting
Surface Mounted

Capacity
Dispenses 250 standard single or half-fold paper toilet seat covers

• Type 304 Stainless Steel - Satin Finish

Covers are self-feeding until supply is depleted. Unit is manually reloaded with a full box through concealed opening in bottom on schedule determined by maintenance requirements.

Unit is surface mounted on wall or partition using two (2) #10 x 1-1/2″ [Ø5 x 40] self-threading screws (by others).

Mounting holes are hidden behind dispenser box for vandal resistant locking but clearly accessible through dispenser slot for installation hanging.

For compliance with 2010 ADA Accessibility Standards, unit should be installed so that dispenser slot is 54″ [1372] maximum above finished floor (AFF) if clear floor side reach access is provided or 48″ [1219] maximum AFF if clear floor forward reach access only is provided or 46″ [1168] maximum AFF if side reach over an obstruction only is provided (ie: vanity).

• Product Care & Maintenance
• Technical Data Sheet – 0477-SM

• Straight Grab Bar
• Snap Flange – cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Peened for better gripping
• Surface Mounted
• Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples
• Mounting flange is 1/8″ (3 mm) thick, type 304 stainless steel
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter

• 18″ (457 mm) – 10-3801-18P
• 36″ (914 mm) – 10-3801-36P
• 42″ (1067 mm) – 3801-42P

Series
3801 Series

Type
Straight Grab Bar – Peened

Dimensions
1-1⁄4″ (32 mm) O.D.

Construction
Type 304 Stainless Steel - Satin Finish

Surface
Peened

Mounting
Surface Mounted

Mounting Flange
Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples; 1/8″ (3 mm) thick, type 304 stainless steel.

Cover
Type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter.

ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1. The fabricated product is designed to support a load in excess of 250 pounds (113.4 kg). Proper wall mounting, anchoring and an adequately sized fastener system are required to meet the specified loading requirements.

• Satin Finish - Peened for better gripping

Use the grab bar as a template to locate and pre-drill the mounting holes. Install each flange with two appropriate #10 self-threading flat or oval head screws or another fastener system suitable for the wall conditions.

Appropriate anchoring and backing must be provided in accordance with applicable building requirements or the architect's plans before the wall is finished.

For 2010 ADA Accessibility Standards, the top of the grab bar should be installed between 33″ [840] minimum and 36″ [915] maximum Above Finished Floor (AFF).

ASI anchors are available separately and should be specified according to the grab bar and mounting conditions.

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 10-3801-18P
• Technical Data Sheet – 10-3801-36P
• Technical Data Sheet – 10-3801-42P