ASI - 0740-Z Robe Hook (Single) – Surface Mounted, Chrome Plated Zamak

• Heavy-duty robe hook
• Fabricated of brass with a chrome finish
• Exposed mounting
• Three (3) 7/32″ diameter (Ø5.6) countersunk mounting holes
• 2-3/4″ diameter (Ø70) flange
• Surface Mounted
• Capable of supporting over 181 lbs. (82 kg) when properly attached to building element

Model
0751-A

Type
Robe Hook (Heavy-Duty) – Surface Mounted (Exposed)

Dimensions
2-3/4″ x 2-3/4″ x 3-1/4 Projection (70 x 70 x 83 mm)

Construction
Heavy Duty Chrome Plated Brass

Mounting
Surface Mounted (Exposed)

Flange Diameter
2-3/4″ (Ø70)

Capacity
Hook is capable of supporting over 181 lbs. (82 kg) when properly attached to building element.

• Satin Chrome

Washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Unit is surface mounted on wall or partition using stainless steel Philips flat or oval head #10 self-threading screws (provided by others to suit wall conditions) in a manner capable of supporting 181 lbs (82 kg).

Ensure that mounting configuration complies with local building codes.

For compliance with 2010 ADA Accessibility Standards install the hook center-line 54″ [1372] maximum Above Finished Floor (AFF) when clear floor side reach access is provided or 48″ [1219] max AFF with clear floor forward reach access only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0751-A

• Jumbo Twin Roll Dispenser
• Holds two 9″ (229 mm) diameter rolls
• Accommodates 2-1⁄4″ or 3″ (57 or 76 mm) diameter cores
• Slide panel exposes other roll when one roll is depleted
• Door cabinet and mounting plate fabricated of 18 gauge type 304 stainless steel with a satin finish
• Two viewing slots reveal toilet tissue rolls inside
• Equipped with tumbler lock
• Surface Mounted

Model
0040

Type
Twin 9″ Jumbo Roll Toilet Tissue Dispenser

Dimensions
20-13⁄16″ x 11-3⁄8″ x 6-3⁄16″ (529 x 289 x 157 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Cabinet & Mounting Plate
18 gauge Type 304 stainless steel

Mounting
Surface Mounted

Capacity
Holds two 9″ (229 mm) diameter rolls

Core Sizes
2-1⁄4″ or 3″ (57 or 76 mm) diameter core

• Satin Finish

Two (2) 9″ [Ø229] outside diameter jumbo rolls of toilet tissue are mounted over 3″ [Ø76] inside diameter (ID) core adapters. Two (2) 2-1/4″ [Ø57] ID core rolls may be used by removing the core adapters.

Whenever one roll of toilet tissue is depleted, the other roll is selected by shifting over the lever at the bottom of the unit.

Viewing slots continuously reveal tissue level. Keylocked door prevents unauthorized access or removal. Tissue supply is replenished on a cycle determined by maintenance needs.

For general utility surface mount unit within 12″ [305] of front of toilet from center line and 31″ [787] above finished floor (AFF) from bottom of unit with five (5) No. 12 x 3/4″ [Ø5.5 x 20] pan head self threading screws (by others), or other types as more suitable to site conditions (by others), including wall type appropriate anchors (by others) as may be required through mounting holes provided.

For compliance with 2010 ADA Accessibility Standards install unit so that centerline of first roll is between 7″ and 9″ [178 to 229] from front of toilet and centerline of rolls is 19″ [483] minimum above finished floor (AFF) to 44″ [1118] max. AFF.

• Product Care & Maintenance
• Technical Data Sheet – 0040

• Single Roll Dispenser
• Type 304 Stainless Steel
• Chrome-plated roller
• Heavy gauge concealed bracket mounts on wall
• Secured with stainless steel set screw
• Holds 1800 sheet standard core roll
• Mounting plates are 18 gauge steel
• Surface Mounted
• For theft-resistant spindle, add R-009 after model number

Series
7305 Series

Type
Toilet Tissue Holder (Single)

Dimensions
7-3/4″ x 2″ x 3-7/8″ (207 x 51 x 98 mm)

Construction
Type 304 Stainless Steel

Roller
Chrome-plated roller

Mounting Plates
18 gauge steel

Mounting
Surface Mounted

Capacity
Holds 1800 sheet standard core roll

• 7305-B – Bright Finish
• 7305-S – Satin Finish

Spring-loaded spindles revolve freely and hold rolls until cores are removed.

Surface mount unit on wall using #10 self-threading screws (by others) through holes provided in mounting plates into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit wall conditions.

Hang post and flange assemblies on mounting plates and tighten setscrews to lock units to plates.

For compliance with ICC/ANSI A-117.1-2003 and 2010 ADA Accessibility Standards install unit so that center line of dispenser is 7″ [178] min to 9″ [229] Max in front of toilet and dispenser center is 15″ [381] Min AFF to 48″ [1219] Max AFF.

Recommended mounting height for general utility is 30″ [762] AFF to centerline of roll and 14″ [356] from front of commode to centerline of dispenser.

• Product Care & Maintenance
• Technical Data Sheet – 7305-B – Bright Finish
• Technical Data Sheet – 7305-S – Satin Finish

• Straight Grab Bar
• Snap Flange - cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Smooth surface
• Surface Mounted
• 18 gauge tubing with 1-1/4″ Outside Diameter [Ø32]
• Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples
• Mounting flange is 1/8″ (3 mm) thick, type 304 stainless steel
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter

• 18″ (457 mm) – 3701-18
• 36″ (914 mm) – 3701-36
• 42″ (1067 mm) – 3701-42

Series
3701 Series

Type
Straight Grab Bar

Tubing
18 gauge tubing with 1-1/4″ Outside Diameter [Ø32]

Construction
Type 304 Stainless Steel - Satin Finish

Surface
Smooth

Mounting
Surface Mounted

Wall Clearance
1-1/2″ [38]

Mounting Flange
Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples; 1/8″ (3 mm) thick, type 304 stainless steel.

Cover
Type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter.

ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 that fabricated product shall be of adequate strength to support a load in excess of 250 pounds (113.4 kg). Mounting to the wall is a critical part of the system to meet this requirement. The fastener system must be adequately sized to withstand the shear, tension or pullout, and torsion loads generated by the maximum loading.

• Satin Finish

Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using two (2) #10 self-threading flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33″ [840] minimum Above Finished Floor (AFF) to 36″ [915] maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series).

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 3701-18
• Technical Data Sheet – 3701-36
• Technical Data Sheet – 3701-42