0210 Traditional™ Paper Towel Dispenser (Multi, C-Fold) – Surface Mounted, Stainless Steel

• "Hide-A-Roll" dispenser holds two rolls
• Holds two rolls up to 5 1/4″ (133 mm) diameter
• 1800 sheet capacity
• Top roll automatically drops in place when bottom roll is used up
• Theft resistant spindles
• Tumbler lock
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted

Model
0030

Type
Toilet Tissue Dispenser, Twin Hide-A-Roll

Dimensions
6″ x 12″ x 6 1/2″ (152 x 305 x 165 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Door
18 gauge Type 304 stainless steel

Cabinet Body & Dispensing Mechanism
22 gauge Type 304 stainless steel

Mounting
Surface Mounted

Capacity
Holds two rolls up to 5 1/4″ (133 mm) diameter (1800 sheets)

• Type 304 Stainless Steel - Satin Finish

Reloading instructions are printed on graphic label inside door.

Bottom roll is depleted prior to top roll automatically dropping into lower position for use.

Empty rollers cannot be removed without key unlocking door.

Unit is surface mounted on wall or partition using four (4) 1/4″ x 1″ [M6 x 25] Philips pan-head self-threading screws (by others) through slots on rear wall into suitable wall preparation (by others).

Top two (2) mounting holes through back are "keyhole" slots for ease in hanging unit on pre-installed screws. Bottom two (2) mounting holes are horizontal slots for ease of adjustment.

For compliance with 2010 ADA Accessibility Standards and 2015 ABA Standards install unit with axis of bottom roller 15″ [381] min AFF (Above Finished Floor) to 48″ [1219] max AFF and centerline of dispenser shall be 7″ [178] min to 9″ [229] max. in front of toilet.

• Product Care & Maintenance
• Technical Data Sheet – 0030

• Double Hook
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• 4″ (102 mm) wide stainless steel bar forms hook at each end
• Hook is suitable for robes or clothing and small carry bags

Model
7345-S

Type
Robe Hook (Double)

Dimensions
4″ x 2″ x 2″ (102 x 51 x 51 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Mounting
Surface Mounted

• 7345-B – Bright Finish
• 7345-S – Satin Finish

Hook is suitable for a robe or clothing and small carry bags.

Surface mount unit on door back or wall using two (2) #10 self-threading screws (by others) through holes provided in mounting plate into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit door or wall conditions. Hang post and flange assembly on mounting plate and tighten set screw to lock unit to plate.

For compliance with ICC/ANSI A-117.1-2003 and 2010 ADA Accessibility Standards, install unit with top of hook 48″ [1219] maximum Above Finished Floor (AFF) or 46″ [1168] max AFF if side reach access over an obstruction (e.g. vanity) with reach depth greater than 10″ [254] and less than 25″ [635] is only provided or 44″ [1118] max AFF if forward reach over an obstruction with reach depth greater than 20″ [508] and less than 25″ [635] is only provided.

For general utility, install hook with centerline of mounting plate 68″ [1727] AFF.

• Product Care & Maintenance
• Technical Data Sheet – 7345-S
• Technical Data Sheet – 7345-B

• Vertical space saving footprint
• All purpose valve and a tamper-resistant refill indicator
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• Manual Push Button Operation
• Liquid Soap - 40 oz. (1.2 L) Capacity

Model
0347

Type
Liquid Soap Dispenser – Vertical – Surface Mounted

Dimensions
4-13/16” x 8-3/16” x 3-15/16” (122 x 208 x 100 mm)

Spout Projection
3⁄4″ (19 mm)

Construction
Type 304 Stainless Steel - Satin Finish

Mounting
Surface Mounted

Capacity
40 fl. oz. (1.2 L)

Operation
Manual Push Button Operation

Soap Requirements
Proper usage of this dispenser requires, that only soap within the following range for viscosity and pH may be used.

Viscosity Range (mPa·s or cP)
100 – 3.5k

pH Range
5.5 ~ 8.5

Soaps containing reportable salts, chlorides and alcohols should be avoided.

• Satin Stainless Steel

Push button to dispense soap. Unit is refilled through hinged door at top requiring special key (supplied) to open.

Soap tank will continue to feed properly until soap level is below valve intake port. Tank supply is replenished manually.

Unit is surface mounted to wall or partition with a wall mounting plate (supplied) and screws (by others). Unit is secured to interlocking wedge bracket and locked in place by a locking screw (supplied) installed through hinged refill door.

Recommended installation for general utility is 42" [1066] Above Finished Floor (AFF) or 6" [152] min above washbasin.

For compliance with 2010 ADA Accessibility Standards and 2015 ABA Standards, install unit with centerline of valve button no higher than 48" [1219] AFF.

• Product Care & Maintenance
• Soap Dispensing Chart
• Technical Data Sheet – 0347

• One-piece stainless steel channel encases mirror and backing
• Tight mitered corners add sophistication
• Type 304, alloy 18-8 stainless steel - Satin Finish Frame
• Plate Glass Mirror
• Surface Mounted
• Various sizes and glazing options
• Mirror is held secure by theft-resistant screws

Series
0620 Series

Type
Stainless Steel Chan-Lok Frame Mirror

Dimensions
Various sizes and glazing options

Mounting
Surface Mounted

Frame
18-8, type 304, 20 gauge stainless steel. Exposed surfaces have satin finish. Edges and corners are burr free.

Glass
Standard glazing is #1 quality, 1/4" [6.4] thick plate/float, silver coated and hermetically sealed with a uniform coating of electrolytic copper plating, warranted against silver spoilage for 15 years. Mirrors meet Federal Spec. DD-M-411C, ASTM C-1503, and ASTM C-1036-91.

Filler
Expanded polyethylene microcell foam sheet material, abrasion resistant and shock absorbing, water resistant, 1/8" [3.2] total layer thickness.

Plate Glass
#1 quality polished, silver coated and hermetically sealed with an electrolytic copper plating. Image quality: BEST

Tempered Glass
1/4" [6.4] thick polished tempered glass with two coats of silver. Image quality: BETTER

Important
The reflective quality of tempered glass is not as true as plate glass. As the reflective surface size increases, regardless of glazing type, the likelihood of distortion also increases.

• Type 304, alloy 18-8 stainless steel - Satin Finish Frame

Install “H” wall brackets level and plumb per diagram location using ONLY #8 or #10 Pan Head screws (by others).

Hang mirror on brackets and tighten locking screw (#6-32Fx3/4" Philips Pan Head, supplied separately taped to mirror back) at bottom (note: this screw should be started prior to hanging mirror on wall bracket).

For compliance with 2010 ADA Accessibility Standards and ABA Standards 2015, bottom edge of reflecting surface should be no higher than 40" [1016] Above Finished Floor.

Mirrors larger than 32 sq. ft. (2.97 m²) are fabricated in two (2) or more sections to provide installation and handling ease.

• Product Care & Maintenance
• Technical Data Sheet – 0620 Series
• Mirror Chart