ASI - 3701 Series Straight Grab Bar

• Straight grab bar
• Snap Flange – cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel – Matte Black Powder Coated
• Smooth surface
• Surface mounted
• 18 gauge tubing with 1-1/2″ Outside Diameter (38 mm)
• Available in 18″, 24″, 36″, 42″ and 48″ lengths
• 1-1/2″ (38 mm) wall clearance

• 3801-18-41 – 18″ Length (457 mm)
• 3801-24-41 – 24″ Length (610 mm)
• 3801-36-41 – 36″ Length (914 mm)
• 3801-42-41 – 42″ Length (1067 mm)
• 3801-48-41 – 48″ Length (1219 mm)

Series
3801-41 Series

Type
Straight Snap Flange Grab Bar

Available Lengths
18″ (457 mm), 24″ (610 mm), 36″ (914 mm), 42″ (1067 mm), 48″ (1219 mm)

Outside Diameter
1-1/2″ (38 mm)

Tubing
18 Gauge Type 304 Stainless Steel

Surface
Smooth

Mounting Flange
3-1/8″ (79 mm) O.D., 1/8″ (3 mm) thick Type 304 stainless steel with 2 screw holes and 3 locking dimples

Snap-On Cover
22 gauge Type 304 stainless steel, 3-3/16″ (81 mm) diameter

Wall Clearance
1-1/2″ (38 mm)

Mounting
Surface Mounted

Capacity
Designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 requirements for a load in excess of 250 lbs (113.4 kg) when properly mounted

• Matte Black Powder Coated Finish

All accessible Matte Black Powder Coated surfaces should be cleaned with a mild liquid soap only. The surfaces should then be wiped and dried.

In areas containing showers, the accessories must receive ventilation from the outside so that excess humidity can escape.

Do not use abrasive powders or scouring pads, water closet cleaners, ceramic tile cleaners, solutions containing more than 1% ammonia by volume, solutions containing acids or lye, or solutions containing enzymes.

Use grab bar as a template to mark mounting hole locations and pre-drill holes.

Install bar using two (2) #10 self-threading flat head or oval head screws (by others), or other suitable fastener system (by others), for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on architectural plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards, install unit so that the top of the grab bar is 33″ (840 mm) minimum Above Finished Floor (AFF) to 36″ (915 mm) maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled.

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 3801-18-41 – 18″
• Technical Data Sheet – 3801-24-41 – 24″
• Technical Data Sheet – 3801-36-41 – 36″
• Technical Data Sheet – 3801-42-41 – 42″
• Technical Data Sheet – 3801-48-41 – 48″

• Straight Grab Bar
• Snap Flange – cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Peened for better gripping
• Surface Mounted
• Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples
• Mounting flange is 1/8″ (3 mm) thick, type 304 stainless steel
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter

• 18″ (457 mm) – 10-3801-18P
• 36″ (914 mm) – 10-3801-36P
• 42″ (1067 mm) – 3801-42P

Series
3801 Series

Type
Straight Grab Bar – Peened

Dimensions
1-1⁄4″ (32 mm) O.D.

Construction
Type 304 Stainless Steel - Satin Finish

Surface
Peened

Mounting
Surface Mounted

Mounting Flange
Concealed mounting flange of 3-1/8″ (79 mm) O.D. diameter with 2 screw holes and 3 locking dimples; 1/8″ (3 mm) thick, type 304 stainless steel.

Cover
Type 304 stainless steel with a satin finish and 22 gauge, 3-3/16″ (81 mm) diameter.

ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1. The fabricated product is designed to support a load in excess of 250 pounds (113.4 kg). Proper wall mounting, anchoring and an adequately sized fastener system are required to meet the specified loading requirements.

• Satin Finish - Peened for better gripping

Use the grab bar as a template to locate and pre-drill the mounting holes. Install each flange with two appropriate #10 self-threading flat or oval head screws or another fastener system suitable for the wall conditions.

Appropriate anchoring and backing must be provided in accordance with applicable building requirements or the architect's plans before the wall is finished.

For 2010 ADA Accessibility Standards, the top of the grab bar should be installed between 33″ [840] minimum and 36″ [915] maximum Above Finished Floor (AFF).

ASI anchors are available separately and should be specified according to the grab bar and mounting conditions.

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 10-3801-18P
• Technical Data Sheet – 10-3801-36P
• Technical Data Sheet – 10-3801-42P

• Straight Grab Bar
• Snap Flange - cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel - Satin Finish
• Surface Mounted
• 18 gauge tubing with 1-1/2" Outside Diameter [Ø38]
• Concealed mounting flange of 3-1/8" [79] O.D. with 2 screw holes and 3 locking dimples
• Cover is type 304 stainless steel with a satin finish and 22 gauge, 3-3/16" [81] diameter

Type
Straight Grab Bar

Material
Type 304 Stainless Steel

Construction
18 gauge tubing with 1-1/2" Outside Diameter [Ø38]

Mounting
Surface Mounted

Mounting Flange
3-1/8" [79] O.D. with 2 screw holes and 3 locking dimples

Mounting Capacity
ASI grab bars are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 that fabricated product shall be of adequate strength to support a load in excess of 250 pounds (113.4 kg). Mounting to the wall is a critical part of the system to meet this requirement. The fastener system must be adequately sized to withstand the shear, tension or pullout, and torsion loads generated by the maximum loading.

• 42" / 10-3801-42
• 36" / 10-3801-36
• 18" / 10-3801-18

Stainless Steel
Satin finish, unless otherwise noted.

Stainless Steel washroom accessory products require regular surface cleaning, much the same as stainless steel sinks, pots and pans and eating utensils.

As long as a regular cleaning schedule is followed, the best method is cleaning with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

For a “new" look, surfaces can be wiped with lemon oil applied by a soft polishing cloth to maintain sheen.

Stainless Steel should be protected against muriatic acid and caustic or abrasive materials, and harsh cleaning detergents [with pH outside the range 7 ± 1.5].

In the event such agents cause discoloration, polishing with a stainless steel cleaner such as 3M™ Stainless Steel Cleaner & Polish® and a soft cloth on bright or mirror finishes, or for satin finish surfaces the Stainless Steel cleaner and 3M™ Scotch Brite® pad either blue (less aggressive) or green (more aggressive) is recommended.

Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using two (2) #10 selfthreading flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" [840] minimum Above Finished Floor (AFF) to 36" [915] maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series).

• Product Care & Maintenance
• Grab Bar Configurations

Technical Data Sheets

• 42" / 10-3801-42 – Technical Data Sheet
• 36" / 10-3801-36 – Technical Data Sheet
• 18" / 10-3801-18 – Technical Data Sheet