ASI - 0030 Toilet Tissue Dispenser, Twin Hide-A-Roll – Surface Mounted

• Straight grab bar
• Snap Flange – cover snaps over mounting flange to conceal screws
• Type 304 Stainless Steel – Matte Black Powder Coated
• Smooth surface
• Surface mounted
• 18 gauge tubing with 1-1/2″ Outside Diameter (38 mm)
• Available in 18″, 24″, 36″, 42″ and 48″ lengths
• 1-1/2″ (38 mm) wall clearance

• 3801-18-41 – 18″ Length (457 mm)
• 3801-24-41 – 24″ Length (610 mm)
• 3801-36-41 – 36″ Length (914 mm)
• 3801-42-41 – 42″ Length (1067 mm)
• 3801-48-41 – 48″ Length (1219 mm)

Series
3801-41 Series

Type
Straight Snap Flange Grab Bar

Available Lengths
18″ (457 mm), 24″ (610 mm), 36″ (914 mm), 42″ (1067 mm), 48″ (1219 mm)

Outside Diameter
1-1/2″ (38 mm)

Tubing
18 Gauge Type 304 Stainless Steel

Surface
Smooth

Mounting Flange
3-1/8″ (79 mm) O.D., 1/8″ (3 mm) thick Type 304 stainless steel with 2 screw holes and 3 locking dimples

Snap-On Cover
22 gauge Type 304 stainless steel, 3-3/16″ (81 mm) diameter

Wall Clearance
1-1/2″ (38 mm)

Mounting
Surface Mounted

Capacity
Designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 requirements for a load in excess of 250 lbs (113.4 kg) when properly mounted

• Matte Black Powder Coated Finish

All accessible Matte Black Powder Coated surfaces should be cleaned with a mild liquid soap only. The surfaces should then be wiped and dried.

In areas containing showers, the accessories must receive ventilation from the outside so that excess humidity can escape.

Do not use abrasive powders or scouring pads, water closet cleaners, ceramic tile cleaners, solutions containing more than 1% ammonia by volume, solutions containing acids or lye, or solutions containing enzymes.

Use grab bar as a template to mark mounting hole locations and pre-drill holes.

Install bar using two (2) #10 self-threading flat head or oval head screws (by others), or other suitable fastener system (by others), for each flange.

Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on architectural plans prior to wall finishing.

For compliance with 2010 ADA Accessibility Standards, install unit so that the top of the grab bar is 33″ (840 mm) minimum Above Finished Floor (AFF) to 36″ (915 mm) maximum AFF.

Anchors are available from ASI and must be specified separately for each grab bar style scheduled.

• Product Care & Maintenance
• Grab Bar Configurations
• Technical Data Sheet – 3801-18-41 – 18″
• Technical Data Sheet – 3801-24-41 – 24″
• Technical Data Sheet – 3801-36-41 – 36″
• Technical Data Sheet – 3801-42-41 – 42″
• Technical Data Sheet – 3801-48-41 – 48″

• Dispenses 250 seat covers
• 20 gauge type 304 stainless steel construction
• Satin finish
• Surface mounted
• Curved front adds strength and elegance
• Concealed, multi-staked piano hinge
• Covers are self-feeding until supply is depleted
• Concealed bottom opening allows manual reloading

Model
20477-SM

Series
Roval™

Type
Surface Mounted Toilet Seat Cover Dispenser

Dimensions
15-3/4″ x 11″ x 2-3/8″ (400 x 280 x 60 mm)

Construction
20 gauge Type 304 Stainless Steel

Finish
Satin Finish

Mounting
Surface Mounted

Capacity
Dispenses 250 seat covers

Hinge
Concealed, Multi-Staked Piano Hinge

• Satin Finish

Covers are self-feeding until supply is depleted. Unit is manually reloaded with a full box through concealed opening in bottom on schedule determined by maintenance requirements.

Regularly inspect and replenish the supply of toilet seat covers according to facility maintenance requirements.

Clean stainless steel surfaces regularly with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Mount unit on wall or partition surface using two (2) #10 x 1-1/4″ [32] self-threading flat head screws (by others).

Mounting holes are accessible through the dispenser slot during installation and are concealed behind the dispenser box after the dispensing product is loaded for vandal-resistant installation.

For compliance with 2010 ADA Accessibility Standards, install unit so that centerline of dispenser slot is 48″ [1219] maximum Above Finished Floor (AFF) if clear floor access is provided.

Where only side reach over an obstruction is provided, such as over a vanity, centerline of dispenser slot should be 46″ [1168] maximum AFF.

• Product Care & Maintenance
• Technical Data Sheet – 20477-SM

• Single robe hook
• Fabricated from rust resistant Zamak
• Stainless steel wall bracket
• Stainless steel hex socket set screw provided along base of flange
• Chrome Plated
• Surface Mounted

Model
0740-Z

Type
Robe Hook (Single)

Dimensions
2-1/8″ x 1-7/16″ x 2-1/8″ (54 x 37 x 54 mm)

Construction
Chrome Plated Zamac

Wall Bracket
Stainless Steel

Mounting
Surface Mounted

• Chrome Plated

Washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Wall bracket is surface mounted using #10 self-threading screws (supplied) through holes provided. Hook is secured to bracket by tightening stainless steel hex socket set screw.

Typical mounting suggestion is 66″ [1676] Above Finished Floor (AFF).

For compliance with 2010 ADA Accessibility Standards, unit should be installed so that top of hook is 54″ [1372] maximum AFF if clear floor side reach access is provided or 48″ [1219] maximum AFF if clear floor forward reach access is provided.

• Product Care & Maintenance
• Technical Data Sheet – 0740-Z

• Heavy-duty robe hook
• Fabricated of brass with a chrome finish
• Exposed mounting
• Three (3) 7/32″ diameter (Ø5.6) countersunk mounting holes
• 2-3/4″ diameter (Ø70) flange
• Surface Mounted
• Capable of supporting over 181 lbs. (82 kg) when properly attached to building element

Model
0751-A

Type
Robe Hook (Heavy-Duty) – Surface Mounted (Exposed)

Dimensions
2-3/4″ x 2-3/4″ x 3-1/4 Projection (70 x 70 x 83 mm)

Construction
Heavy Duty Chrome Plated Brass

Mounting
Surface Mounted (Exposed)

Flange Diameter
2-3/4″ (Ø70)

Capacity
Hook is capable of supporting over 181 lbs. (82 kg) when properly attached to building element.

• Satin Chrome

Washroom accessory products require regular surface cleaning. Clean with a soft clean rag moistened with a mild detergent, followed by a water-moistened clean rag and then a dry rag.

Unit is surface mounted on wall or partition using stainless steel Philips flat or oval head #10 self-threading screws (provided by others to suit wall conditions) in a manner capable of supporting 181 lbs (82 kg).

Ensure that mounting configuration complies with local building codes.

For compliance with 2010 ADA Accessibility Standards install the hook center-line 54″ [1372] maximum Above Finished Floor (AFF) when clear floor side reach access is provided or 48″ [1219] max AFF with clear floor forward reach access only provided.

• Product Care & Maintenance
• Technical Data Sheet – 0751-A